Tab Content
  • zaza's Avatar
    12-01-19, 09:29 PM
    zaza replied to a thread ransome ts 80 in Classic Machinery
    I didn't do a lot with a TS83 (3 furrow reversible) and so maybe it was like that. I used a TS81 and 2 x TS82 ploughs extensively, 2 on YL bodies,...
    21 replies | 1967 view(s)
  • zaza's Avatar
    12-01-19, 05:49 PM
    zaza replied to a thread ransome ts 80 in Classic Machinery
    The plough in the first video has a turnover mechanism that I have never seen on a manual turnover Ransome plough. There is no collar that moves...
    21 replies | 1967 view(s)
  • zaza's Avatar
    12-01-19, 08:29 AM
    zaza replied to a thread Westerwold Spring Drilling in Cropping
    What he said. Plus I would never drill grass seeds this early. We are pretty certain to get some lousy weather yet this Winter, we haven't had any...
    3 replies | 237 view(s)
  • zaza's Avatar
    12-01-19, 07:55 AM
    zaza replied to a thread ransome ts 80 in Classic Machinery
    Your IH 584 should pick the plough up high enough to enable turnover, even a MF 135 will do that. Make sure that your lift rods are short enough to...
    21 replies | 1967 view(s)
  • zaza's Avatar
    11-01-19, 09:54 AM
    zaza replied to a thread ransome ts 80 in Classic Machinery
    No, when you lift the plough it will centralise (always assuming of course that you don't have any stabiliser bars fitted to your tractor and that...
    21 replies | 1967 view(s)
  • zaza's Avatar
    10-01-19, 11:02 PM
    zaza replied to a thread ransome ts 80 in Classic Machinery
    The plough cross shaft is free to move approximately 1/4 of a turn and when the plough is lowered into work the linkage arms pull the pins on the end...
    21 replies | 1967 view(s)
  • zaza's Avatar
    08-01-19, 10:33 AM
    I couldn't possibly comment. ;)
    20 replies | 1165 view(s)
  • zaza's Avatar
    07-01-19, 11:44 PM
    Thanks for that John. I'll get some suds in an oil can I think before I do any more. I do have to align each pair of bushes but I thought that if I...
    20 replies | 1165 view(s)
  • zaza's Avatar
    07-01-19, 10:36 PM
    Yes, I will be able to get everything into the drill table vice and then I can bolt that down to the table.
    20 replies | 1165 view(s)
  • zaza's Avatar
    07-01-19, 05:30 PM
    UPDATE. Today ZaZa drilled a hole ! I set up a 54mm hole saw in it's holder and fastened it all in the chuck. I then grabbed a scrap piece of 4"...
    20 replies | 1165 view(s)
  • zaza's Avatar
    07-01-19, 12:59 PM
    Thanks Jack, I had a brief look at those but my problem is that I will almost certainly never use it again if I buy one and they aren't cheap just to...
    20 replies | 1165 view(s)
  • zaza's Avatar
    07-01-19, 10:19 AM
    Thanks John, I'm going to have a go in the next day or two. I watched a few videos on YouTube last night and a couple of them had got ideas about...
    20 replies | 1165 view(s)
  • zaza's Avatar
    06-01-19, 10:11 PM
    Thanks FF. Ideally I want to drill 4 x 50mm holes in 10mm plate (and we do Metric here I'll have you know !!! :rolleyes:) If I got really carried...
    20 replies | 1165 view(s)
  • zaza's Avatar
    06-01-19, 10:03 PM
    Thanks John. Maybe I should have mentioned that I have a couple of 3-jaw chucks with a MT2 shank. I am just a bit concerned about the thickness of...
    20 replies | 1165 view(s)
  • zaza's Avatar
    06-01-19, 05:06 PM
    I want to put some bushes in pieces of 10mm steel plate. The steel tube that I have for the bushes is 50mm OD. I have a 6 speed 3 ph Corona...
    20 replies | 1165 view(s)
  • zaza's Avatar
    23-12-18, 08:59 AM
    zaza replied to a thread Happy Christmas in Agricultural Matters
    And a Happy Christmas to you Joyce. Long time - no chat. Hope all is well with you.
    10 replies | 1503 view(s)
  • zaza's Avatar
    20-12-18, 04:39 PM
    Water canon :D
    7 replies | 1014 view(s)
  • zaza's Avatar
    19-12-18, 01:45 PM
    zaza replied to a thread Happy Christmas in Agricultural Matters
    Same from me to everyone on here.
    10 replies | 1503 view(s)
No More Results
About zaza

Basic Information

Statistics


Total Posts
Total Posts
1,473
Posts Per Day
0.68
General Information
Join Date
16-02-13
Referrals
0