Tab Content
  • zaza's Avatar
    13-08-18, 10:35 AM
    We've got buzzards and ravens in a wood 200 yards away. They would have any chicks which is perhaps why we haven't seen any for years but would they...
    7 replies | 134 view(s)
  • zaza's Avatar
    13-08-18, 07:49 AM
    Yes, so was I. But at least charlie can't get at them up there. Thanks Barney.
    7 replies | 134 view(s)
  • zaza's Avatar
    12-08-18, 03:57 PM
    zaza replied to a thread Which grass seed mix? in Cropping
    With the racehorse job if it wasn't cut by the 2nd week of june then you could forget about it for that market, and the two really decent chaps that...
    9 replies | 179 view(s)
  • zaza's Avatar
    12-08-18, 11:04 AM
    continuation............
    7 replies | 134 view(s)
  • zaza's Avatar
    12-08-18, 11:02 AM
    Just goes to prove that you're never too old to learn. I had always thought that partridges always jugged on the ground but it appears not to be...
    7 replies | 134 view(s)
  • zaza's Avatar
    11-08-18, 08:23 PM
    zaza replied to a thread Which grass seed mix? in Cropping
    Some annual and perennial ryegrass need to be in the mix, as well as a small amount of clover - some red and some white which will leave a bit of...
    9 replies | 179 view(s)
  • zaza's Avatar
    11-08-18, 05:07 PM
    zaza replied to a thread Which grass seed mix? in Cropping
    Again it all depends on the type of horse market you are aiming for. I grew 40-ish acres for the racehorse trade for many years as well as making...
    9 replies | 179 view(s)
  • zaza's Avatar
    11-08-18, 10:45 AM
    Thanks everybody. Didn't realise it would be appreciated like that. But I feel that I need to add that although I used Photoshop to stitch 3 photos....
    5 replies | 123 view(s)
  • zaza's Avatar
    11-08-18, 06:54 AM
    Two nights ago we had an amazing sunset here. I couldn't get it all in one shot and so took three and stitched them together with Photoshop.
    5 replies | 123 view(s)
  • zaza's Avatar
    09-08-18, 10:55 PM
    zaza replied to a thread Which grass seed mix? in Cropping
    Could you expand on "early cut" please ? And what is the hay to be fed to ?
    9 replies | 179 view(s)
  • zaza's Avatar
    02-08-18, 07:52 AM
    zaza replied to a thread FQAS in Agricultural Matters
    Send them a copy of your invoice but either blank out all the financial figures or substitute them with some fictitious ones. As long as it shows the...
    4 replies | 250 view(s)
  • zaza's Avatar
    01-08-18, 09:25 AM
    That all depends on the formulation of the glyphosate in the mix. i.e. the strength. Is it 360gms/lt, 480, or 520 ? With all due respect you are...
    6 replies | 246 view(s)
  • zaza's Avatar
    21-07-18, 04:21 PM
    zaza replied to a thread JCB 3CX 1986 Overheating in Machinery
    Which side of the radiator did you check ? Remember it is probably a pusher fan, i.e. it doesn't suck air in from the front, it sucks it in from the...
    8 replies | 345 view(s)
  • zaza's Avatar
    17-07-18, 02:52 PM
    zaza replied to a thread Arc welding cast ? in Workshop Projects
    Thanks Jack. But you know how litigious some people can be these days. Best not to take any chances. :D
    8 replies | 399 view(s)
  • zaza's Avatar
    16-07-18, 08:29 PM
    Didn't know that. Thanks WRSNI. There was one problem with a fan on the knotters of a 701. Most of the sledges in those days were manned. And if you...
    10 replies | 389 view(s)
  • zaza's Avatar
    16-07-18, 04:40 PM
    zaza replied to a thread Arc welding cast ? in Workshop Projects
    I hope the job works out O.K. Payment is tomorrow night in the pub. The repair came with a concrete guarantee. I told him that the guarantee lasted...
    8 replies | 399 view(s)
  • zaza's Avatar
    16-07-18, 04:36 PM
    Very little experience with Massey balers. I used a 10 or a 15 I think it was when I worked on a farm but when I started up on my own I needed to buy...
    10 replies | 389 view(s)
  • zaza's Avatar
    16-07-18, 09:32 AM
    You will find that sisal is easier on your hands than poly, especially if you're not used to handling many bales. I think rodents like it a bit more...
    10 replies | 389 view(s)
  • zaza's Avatar
    16-07-18, 09:26 AM
    zaza replied to a thread Arc welding cast ? in Workshop Projects
    Thank you WRSNI for your advice. The job was for a friend of mine who has a loader on his 956 and he caught a tree branch and it came down the loader...
    8 replies | 399 view(s)
No More Results
About zaza

Basic Information

Statistics


Total Posts
Total Posts
1,435
Posts Per Day
0.72
General Information
Join Date
16-02-13
Referrals
0