• Footsfitter's Avatar
    06-12-17, 04:32 PM
    Can you post pictures? that would be helpful and I will see if I can point someone this way for advice
    11 replies | 470 view(s)
  • Footsfitter's Avatar
    05-12-17, 09:44 PM
    Morris oils nearest match comes up with 59-64ltrs of liquimatic JDF (same as NH stripey transmission oil) The rear hubs are lubricated from the...
    8 replies | 722 view(s)
  • Footsfitter's Avatar
    05-12-17, 09:36 PM
    Footsfitter replied to a thread Job 1135 in Machinery
    Till you've figured out what happened I'd play safe and knock the main gearlever into neutral as well the shuttle lever:eek:
    5 replies | 328 view(s)
  • Footsfitter's Avatar
    03-12-17, 10:01 PM
    I'll take a stab at this question only because Andrew from A&R warned me about it. I'm guessing you have replaced the filter, (or some one has) and...
    11 replies | 470 view(s)
  • Footsfitter's Avatar
    01-12-17, 09:47 PM
    The best tool/aid is a digital camera. Take loads of images especially if mundane pipes, cables and looms before you start disturbing them too much....
    5 replies | 327 view(s)
  • Footsfitter's Avatar
    30-11-17, 11:37 PM
    Whoa! I wouldn't like to go that far, a little maybe, but "something" is pushing it a bit far! Trouble is I've tended to do just the one of several...
    5 replies | 327 view(s)
  • Footsfitter's Avatar
    30-11-17, 01:59 PM
    There was no need, it worked out just right with that size of channel and the shafts diameter, to get the disc edge near to the work meant the...
    3 replies | 342 view(s)
  • Footsfitter's Avatar
    30-11-17, 12:20 AM
    Once we were down to within 0.5mm of the target 90mm diameter things changed to polishing the built up section with emery tape and then repeated...
    3 replies | 342 view(s)
  • Footsfitter's Avatar
    30-11-17, 12:08 AM
    Had a small welding job to do on the headstock of a Kuhn 5f master 120 plough- the pin welded just above the top link holes on the rear of the...
    3 replies | 342 view(s)
  • Footsfitter's Avatar
    27-11-17, 12:09 AM
    Footsfitter replied to a thread manitou 527 in Machinery
    Looking at a mitas tyre chart for both sizes it seems that the larger width tyre may have a 40mm longer rolling circumference which may be ok if you...
    4 replies | 379 view(s)
  • Footsfitter's Avatar
    20-11-17, 10:18 PM
    Or the pumps internal lever is right up on top of the camshaft lobe? gently turn the engine over while trying the lever and you should find that...
    6 replies | 469 view(s)
No More Results
About ploughman24

Basic Information

Date of Birth
October 28, 1953 (64)
About ploughman24
Location:
plymouth/devon
Occupation:
disabeled

Signature


do not put off those jobs that you can do today till tomorrow

Statistics


Total Posts
Total Posts
17
Posts Per Day
0.01
General Information
Last Activity
27-09-17 06:36 PM
Join Date
16-02-13
Referrals
0

3 Friends

  1. Footsfitter Footsfitter is offline

    Senior Member

    Footsfitter
  2. Joyce Joyce is offline

    Senior Member

    Joyce
  3. stockslave stockslave is offline

    Member

    stockslave
Showing Friends 1 to 3 of 3