Tab Content
  • ACE's Avatar
    Yesterday, 10:22 PM
    ACE replied to a thread Manitou warning lamp in Machinery
    Its low brake fluid level. take left hand dash panel off and have a look, could be iffy sensor in cap. if its low and its not the master cylinder...
    3 replies | 52 view(s)
  • ACE's Avatar
    14-01-18, 05:28 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    Drain/Level and filler bungs you mean on axle? if you look closer there are 3 drain bungs, 1 in the centre and 2 underneath one each side. ...
    11 replies | 265 view(s)
  • ACE's Avatar
    14-01-18, 05:22 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    The oil I recommend is genuine Manitou oil "special wet brake lubricant" there are other oil brands that claim to do the job but they don't always...
    11 replies | 265 view(s)
  • ACE's Avatar
    14-01-18, 12:43 AM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    May have been limited slip diff in front axle or brakes? An oil change using genuine Manitou axle oil will normally cure that. Oil in hubs isn't to...
    11 replies | 265 view(s)
  • ACE's Avatar
    12-01-18, 08:47 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    Hello Obviously check oil level but if it making a noise chances are it needs alot more than just oil. Jack it up check play on wheel bearings...
    11 replies | 265 view(s)
  • ACE's Avatar
    12-01-18, 08:42 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    I'm here ;) just busy
    11 replies | 265 view(s)
  • ACE's Avatar
    03-01-18, 01:03 AM
    ACE replied to a thread Deutz starter in Machinery
    Found a 4kw iskra, send you a PM:) Edit oh I cant cause your new and they not switched on. its expensive just over 300 plus vat, if your...
    2 replies | 170 view(s)
  • ACE's Avatar
    02-01-18, 08:22 PM
    ACE replied to a thread Deutz starter in Machinery
    Probably i will have a look this evening.
    2 replies | 170 view(s)
  • ACE's Avatar
    21-12-17, 09:14 AM
    Either diaphragm for the boost is blown on the top of injector pump or the pin it operates is stuck in. The pin should be sprung loaded out or pushed...
    4 replies | 497 view(s)
  • ACE's Avatar
    20-12-17, 09:09 AM
    Many things will affect boost pressure. While i dont know what max pressure should be i do know the delphi injector pumps are very bad for problems...
    4 replies | 497 view(s)
  • ACE's Avatar
    18-12-17, 07:41 PM
    Have a feeling these have a bosch pump with a boost diaphragm on the top. If so care needs to be taken when replacing as its easy to put them back...
    2 replies | 241 view(s)
No More Results
About All2dairy

Basic Information

About All2dairy
Location:
Enniskillen co.fermanagh
Occupation:
Farmer

Statistics


Total Posts
Total Posts
11
Posts Per Day
0.02
General Information
Last Activity
06-01-18 11:53 PM
Join Date
16-06-16
Referrals
0

1 Friend

  1. ACE ACE is offline

    Senior Member

    ACE
Showing Friends 1 to 1 of 1