Footsfitter
Senior Member

Well you could cobble it up on the 3 spools for now fairly easily? Then how about looking for a joystick & triple valve block off of a hedgetrimmer...

spotting your username reminded me of the old late boss once suggesting his V8 RangeRover was using less petrol than my fully loaded works truck - a...

Good find! Can't remember where I found a copy for the RTV900 we have, but like the one above they can often be tucked away on obscure websites...

If no one can come up with the info, try further afield on this site in the USA- http://www.orangetractortalks.com/forums/

I expect the 114hp could be the engines actual rating at the flywheel with little extras and ancillaries fitted to the power unit as these will sap...

Heres a link to Tractordata.com for your mount http://www.tractordata.com/farm-tractors/000/8/9/899-massey-ferguson-6265.html "You need a...

Note as of April 2018 Postimage are in dispute with the powers at be regarding their use of the .org web address and this has resulted in the...

Not a machine I'm familiar with but often makers limit reverse speeds but reducing the number of gears available or in the case of hydrostatics by...

Main thing is not to make the puller plate too big and damage the block- more of an issue where some types have the sealing orings on the liner and...

Mrs Gee ? :rolleyes::eek::D

Yes, the pump was tested on stanadyne stand by a specialist. I will by an endoscopy camera in order to verify the crankshaft sensor to see if there...

Do you mean that the pump has been mounted on a test bed and checked by an injection specialist? Only other thought is if there is a crankshaft...

I have come across some that you can unscrew the inner male bit, usually needs the gland nut undone to allow the inner bit and lead/wires to rotate,...

Bit difficult to see the exact type without a better view of the plug end on & is there any lettering to give a clue? I'd look with a search on...

Don't get confused with the shiny tube also on his lap John, thats the catheter out of his bag..............:eek:

We had a 697RTZ for a while, JD 6cylinder with a rotary pump and ECU for the pump. Pulled into the yard with a trailer load of corn, stopped the...

Hi John, The word "Occasionally" may have a lot to do with it and blue fumes on & off with the throttle say ring wear or gumming up? I expect...

Oooh, Hi-Drive sprocket generation claterpillar, no wonder it had new-fangled electric stuff on it! The newest I worked on before leaving the...

There was a well known old boy by the name of Nelson Green from up Lincolnshire way who used his demob money after WW2 to buy a bit of land and setup...

Well if any of the solenoids/valves are interchangable you can rule them out and even replace the gasket under the block, which in the absence of...

Maybe the old 527/58 tranny was something they were still good at? So far the only issue was a new pressure switch leaked after a few weeks, sent a...

I have stopped using the for overhauls now. Had nothing but hassle with them and problems. Just not good enough when they charge top price i want it...

If its in need of overhauling, these will do it to the same spec as an OE exchange unit at a fraction of the OEM's cost. :rolleyes: ...

I agree with you FF. knackered seals or cracked clutch pack drum letting pressure from one side to the other when hot as the crack pens up? f/r...

Sounds like your getting reverse in a forward gear which will act as a brake. The oil getting hot could also be a clue in that something is slipping...

Not much comes up on the common NG suppliers but this Perkins US site may give an idea that the housing is available separately - ...

Looks like the cooler housing has split. Agco says Not available, only complete item supplied! I'd try Perkins/powerpart or some of the non-genuine...