• ACE's Avatar
    09-12-17, 12:53 PM
    ACE replied to a thread Manitou MT 928-4 in Workshop Projects
    Kind of annoys me when people ask a question on here then never bother to come back and find the answer. :mad:
    10 replies | 430 view(s)
  • ACE's Avatar
    06-12-17, 06:13 PM
    ACE replied to a thread Manitou MT 928-4 in Workshop Projects
    See drawing attached, the reg valve is item 14 in red. the old ones had a brass sleeve on them which would wear and pull over the head of the screw....
    10 replies | 430 view(s)
  • ACE's Avatar
    06-12-17, 05:05 PM
    ACE replied to a thread Manitou MT 928-4 in Workshop Projects
    There was an issue with the pressure regulating valve in the f/r valve block on the early machines, there was a updated replacement valve at the time...
    10 replies | 430 view(s)
  • Footsfitter's Avatar
    06-12-17, 04:32 PM
    Can you post pictures? that would be helpful and I will see if I can point someone this way for advice
    10 replies | 430 view(s)
  • Footsfitter's Avatar
    05-12-17, 09:44 PM
    Morris oils nearest match comes up with 59-64ltrs of liquimatic JDF (same as NH stripey transmission oil) The rear hubs are lubricated from the...
    8 replies | 706 view(s)
  • Footsfitter's Avatar
    05-12-17, 09:36 PM
    Footsfitter replied to a thread Job 1135 in Machinery
    Till you've figured out what happened I'd play safe and knock the main gearlever into neutral as well the shuttle lever:eek:
    5 replies | 309 view(s)
  • Footsfitter's Avatar
    03-12-17, 10:01 PM
    I'll take a stab at this question only because Andrew from A&R warned me about it. I'm guessing you have replaced the filter, (or some one has) and...
    10 replies | 430 view(s)
  • Footsfitter's Avatar
    01-12-17, 09:47 PM
    The best tool/aid is a digital camera. Take loads of images especially if mundane pipes, cables and looms before you start disturbing them too much....
    5 replies | 310 view(s)
  • Footsfitter's Avatar
    30-11-17, 11:37 PM
    Whoa! I wouldn't like to go that far, a little maybe, but "something" is pushing it a bit far! Trouble is I've tended to do just the one of several...
    5 replies | 310 view(s)
  • Footsfitter's Avatar
    30-11-17, 01:59 PM
    There was no need, it worked out just right with that size of channel and the shafts diameter, to get the disc edge near to the work meant the...
    3 replies | 322 view(s)
  • Footsfitter's Avatar
    30-11-17, 12:20 AM
    Once we were down to within 0.5mm of the target 90mm diameter things changed to polishing the built up section with emery tape and then repeated...
    3 replies | 322 view(s)
  • Footsfitter's Avatar
    30-11-17, 12:08 AM
    Had a small welding job to do on the headstock of a Kuhn 5f master 120 plough- the pin welded just above the top link holes on the rear of the...
    3 replies | 322 view(s)
  • ACE's Avatar
    27-11-17, 07:45 PM
    ACE replied to a thread manitou 527 in Machinery
    Should be fine if doing all 4. I think 405 is a factory fit option anyway. Change the mud gaurds and you could fit 24" tyres and rims if you want.
    4 replies | 365 view(s)
  • Footsfitter's Avatar
    27-11-17, 12:09 AM
    Footsfitter replied to a thread manitou 527 in Machinery
    Looking at a mitas tyre chart for both sizes it seems that the larger width tyre may have a 40mm longer rolling circumference which may be ok if you...
    4 replies | 365 view(s)
  • Footsfitter's Avatar
    20-11-17, 10:18 PM
    Or the pumps internal lever is right up on top of the camshaft lobe? gently turn the engine over while trying the lever and you should find that...
    6 replies | 456 view(s)
  • ACE's Avatar
    19-11-17, 11:16 AM
    ACE replied to a thread Manitou 634 overheating in Machinery
    With a user name like that i assuming you see a few:rolleyes:
    4 replies | 564 view(s)
  • ACE's Avatar
    18-11-17, 04:26 PM
    ACE replied to a thread Manitou 634 overheating in Machinery
    I was going to send you a PM but there not switched on yet as your new here:undecided: If you need Manitou part number 224053 give me a shout;)
    4 replies | 564 view(s)
  • Footsfitter's Avatar
    13-11-17, 10:43 PM
    If someones put anything other than LHM the seals will be wrecked
    395 replies | 247532 view(s)
No More Results
About Footsfitter

Basic Information

About Footsfitter
Location:
Basingstoke, Hants

Signature


The best thing about Facebook is the logout button......

Statistics


Total Posts
Total Posts
2,415
Posts Per Day
1.37
General Information
Join Date
15-02-13
Referrals
4

2 Friends

  1. ACE ACE is offline

    Senior Member

    ACE
  2. ploughman24 ploughman24 is offline

    Junior Member

    ploughman24
Showing Friends 1 to 2 of 2