Tab Content
  • ACE's Avatar
    16-01-18, 10:22 PM
    ACE replied to a thread Manitou warning lamp in Machinery
    Its low brake fluid level. take left hand dash panel off and have a look, could be iffy sensor in cap. if its low and its not the master cylinder...
    3 replies | 71 view(s)
  • ACE's Avatar
    14-01-18, 05:28 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    Drain/Level and filler bungs you mean on axle? if you look closer there are 3 drain bungs, 1 in the centre and 2 underneath one each side. ...
    11 replies | 293 view(s)
  • ACE's Avatar
    14-01-18, 05:22 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    The oil I recommend is genuine Manitou oil "special wet brake lubricant" there are other oil brands that claim to do the job but they don't always...
    11 replies | 293 view(s)
  • ACE's Avatar
    14-01-18, 12:43 AM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    May have been limited slip diff in front axle or brakes? An oil change using genuine Manitou axle oil will normally cure that. Oil in hubs isn't to...
    11 replies | 293 view(s)
  • ACE's Avatar
    12-01-18, 08:47 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    Hello Obviously check oil level but if it making a noise chances are it needs alot more than just oil. Jack it up check play on wheel bearings...
    11 replies | 293 view(s)
  • ACE's Avatar
    12-01-18, 08:42 PM
    ACE replied to a thread Manitou 627 Hub Issue in Machinery
    I'm here ;) just busy
    11 replies | 293 view(s)
  • ACE's Avatar
    03-01-18, 01:03 AM
    ACE replied to a thread Deutz starter in Machinery
    Found a 4kw iskra, send you a PM:) Edit oh I cant cause your new and they not switched on. its expensive just over 300 plus vat, if your...
    2 replies | 180 view(s)
  • ACE's Avatar
    02-01-18, 08:22 PM
    ACE replied to a thread Deutz starter in Machinery
    Probably i will have a look this evening.
    2 replies | 180 view(s)
  • ACE's Avatar
    21-12-17, 09:14 AM
    Either diaphragm for the boost is blown on the top of injector pump or the pin it operates is stuck in. The pin should be sprung loaded out or pushed...
    4 replies | 511 view(s)
  • ACE's Avatar
    20-12-17, 09:09 AM
    Many things will affect boost pressure. While i dont know what max pressure should be i do know the delphi injector pumps are very bad for problems...
    4 replies | 511 view(s)
No More Results
About ACE

Basic Information

About ACE
Location:
Oxfordshire
Occupation:
Spanners!

Signature


Statistics


Total Posts
Total Posts
1,520
Posts Per Day
0.85
General Information
Last Activity
Today 06:11 PM
Join Date
16-02-13
Referrals
1

8 Friends

  1. All2dairy All2dairy is offline

    Junior Member

    All2dairy
  2. CleanfixUK CleanfixUK is offline

    Junior Member

    CleanfixUK
  3. Footsfitter Footsfitter is offline

    Senior Member

    Footsfitter
  4. jd69 jd69 is offline

    Senior Member

    jd69
  5. sprocket sprocket is offline

    Senior Member

    sprocket
  6. T P T P is offline

    Senior Member

    T P
  7. Timbo Timbo is offline

    Senior Member

    Timbo
  8. zsnotdead zsnotdead is offline

    Senior Member

    zsnotdead
Showing Friends 1 to 8 of 8