Search:

Type: Posts; User: CPP

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    1,566

    Re: KEMPER HEADER FOR WHOLECROP

    Run thr header in high speed make sure all blade are good and sharp
    cleaner have good square edges
    depending on header age there is some parts to take out and fit for crop flow
  2. Replies
    3
    Views
    5,575

    Re: Starfire 2 or new reciever?

    Is your iTC sf2ready
    if it's transfer it to a sf3000 and trade up to a sf 3000

    We have a lot of guys drilling on sf1 and it works fine may have to shift track a little more

    some say sf1 on...
  3. Replies
    2
    Views
    5,029

    Re: Jd auto steer & lexion

    Fitted many universal steering kit to lexions and work very well
    Spend a bit of time setting it up and away you go
  4. Thread: JD 6170 R

    by CPP
    Replies
    16
    Views
    7,920

    Re: JD 6170 R

    Depends on work type but I would chose DD out side of root crop or very slow speeds
  5. Thread: JD 6170 R

    by CPP
    Replies
    16
    Views
    7,920

    Re: JD 6170 R

    This is only part of the story
    the fuel saving will make up more of the difference over a vairo transmission
    and more area covered
  6. Replies
    5
    Views
    1,158

    Re: Matbro270 joystick fuse blowing

    Check the seat switch and wiring out of back of seat
  7. Replies
    16
    Views
    5,456

    Re: JD 8RT Radio controls

    Glad to help
    I would get the battery's replaced
  8. Replies
    16
    Views
    5,456

    Re: JD 8RT Radio controls

    try pulling radio fuse out and refit
  9. Replies
    4
    Views
    6,701

    Re: John deere / amazone

    yes amazone can do iso bus or send vair rate to amatron
  10. Thread: Matbro 1996 TS280

    by CPP
    Replies
    11
    Views
    6,571

    Re: Matbro 1996 TS280

    Did use to have a problem with main earth in middle of chassis from battery and
    also they use a hyd dump valve to dump pressure from Hyde to allow easy cranking
    this was a mod
  11. Replies
    2
    Views
    5,644

    Re: greenstar universal and auto section switching

    Universal auto Trac not a problem
    section control only by iso bus
    the only way would be to use a raven smart boom kit and use the GPS position from starfire
  12. Thread: fendt to use EGR

    by CPP
    Replies
    13
    Views
    6,191

    Re: fendt to use EGR

    And twin turbo

    2 different ways of meeting stage 3b and now final tier 4 will lead most engine manufacture down the same
    route


    whos was right and who was wrong ???
  13. Thread: maize

    by CPP
    Replies
    36
    Views
    21,970

    Re: maize

    the new claas harvesters round here all has Kemper headers its the only header to have
    and that said by both customer and contractors
    there feed well in the shorter crop
    and leaves the field...
  14. Thread: maize

    by CPP
    Replies
    36
    Views
    21,970

    Re: maize

    the new claas harvesters round here all has Kemper headers its the only header to have
    and that said by both customer and contractors
    there feed well in the shorter crop
    and leaves the field...
  15. Replies
    17
    Views
    17,071

    Re: SF1 accuracy in the real world

    Rtk will help yes
    Are you getting glonass sats as well
    Changing colour won't help as all use same sats
  16. Replies
    17
    Views
    17,071

    Re: SF1 accuracy in the real world

    What type of starfire are you using iTC or sf3000
    not have a lot of problem about here but
    i have seen some very poor satellite consolation
  17. Replies
    17
    Views
    17,071

    Re: SF1 accuracy in the real world

    I would always recommend sf2 for drilling but I know of guys getting on very well with SF1 for many jobs
    including drilling
    the only thing you may have to do is chance the width to suit and may...
  18. Thread: JD 20 series

    by CPP
    Replies
    3
    Views
    6,291

    Re: JD 20 series

    Yes you can fir a full JD auto steer kit to the tractor depending on the age and serial
    or you can fit a universal steering kit which works very well and a cheaper option
  19. Thread: 710 or 650?

    by CPP
    Replies
    12
    Views
    5,555

    Re: 710 or 650?

    How about going 710 /75r42 and ploughing on the land
  20. Replies
    1
    Views
    2,228

    Re: SF2 and Vaderstad Drill

    set up a 6meter today put in 5.98m and no offset and it measured spot on system disc


    set up 4m with old style disc and and had to use a 6 cm offset to the left stangly the coulters measured...
  21. Replies
    7
    Views
    4,292

    Re: JD 6920 hot transmission oil

    How olds the 6920
    it could be if it has a electric pump on front right side of engine or the fuse as sometime had this burn out
    pit could have air in the coolant system bleed air out on bleed...
  22. Replies
    7
    Views
    3,704

    Re: ECU replacement John Deere

    Is it still playing up or has it sorted its self out
  23. Thread: GS3 command center

    by CPP
    Replies
    4
    Views
    2,474

    Re: GS3 command center

    depends on dealer
    you will need to talk to them
  24. Thread: GS3 command center

    by CPP
    Replies
    4
    Views
    2,474

    Re: GS3 command center

    Only way is to put them in gatekeeper then back out to command screen
  25. Replies
    3
    Views
    2,430

    Re: Greenstar Original display

    I'm afraid Not the original display and prosessor and Key card
    will not work in late 30 series nor the new 6R
Results 1 to 25 of 31
Page 1 of 2 1 2