Search:

Type: Posts; User: essexpete

Page 1 of 20 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    429
    Views
    292,814

    Re: Ford New Holland 8340 SLE help thread

    I am afraid that although a user I am no expert. I do wonder if you have one of the electrical components faulty. Have you been able to carry out the more complicated calibration with the switch...
  2. Replies
    37
    Views
    1,210

    Re: improving ground for sale purposes

    Jack have you not got to just be the boss on paper and keep signing a few papers to not be retired? Hate to mention as well but important for anyone registering a death in the farming world not to...
  3. Replies
    37
    Views
    1,210

    Re: improving ground for sale purposes

    https://www.gov.uk/capital-gains-tax/rates

    This might be of help?
  4. Replies
    8
    Views
    508

    Re: how to operate a square baler

    If you get it checked over and running free have you got some straw you could run through it?
  5. Replies
    8
    Views
    508

    Re: how to operate a square baler

    Start with a handbook if you can find one for a NH or very similar model. I note the PTO shaft and fly wheel are not guarded properly so for christ's sake be careful. The baler is one very dangerous...
  6. Re: Sanderson teleporter2 6.22 what type oil?

    I think ACE recommends LS EP 80w90 gear oil in the wet type hubs and the front axle may have limited slip diff. Our old 725 creeps on the tilt, I think it will be seals int tilt and or compensator...
  7. Re: Lawrence Edwards Supa Pac 7000E Bale Wrapper

    The manual model has a couple of hooks underneath to stop the bed rotating when tipping off. Is there something similar? They would not be used to actually stop the bed.
  8. Re: Concave calamity and gone with the wind...........

    The loader driver took the bull by the horns. Potentially could have been horrendous. All too easy to think of the fire lads back at the station sitting around or kipping.
  9. Replies
    6
    Views
    491

    Re: Perkins 203 running rich.

    Has it got a heater unit supplied with fuel on the air intake manifold?
  10. Replies
    8
    Views
    468

    Re: JCB 3CX 1986 Overheating

    Should think it would be a Perkins 236
  11. Replies
    4
    Views
    365

    Re: Manitou mlt 526

    Ace (member on here) with luck will be be along to advise. In the mean time it sounds a bit like a problem I had with the wrong oil and the limited slip diff on a 725 MLT. I had front brake squark...
  12. Replies
    8
    Views
    468

    Re: JCB 3CX 1986 Overheating

    Yes plus 1 to Zazza, I got caught out years ago with a 3 C thinking the rad was clean. Personally I would put a new thermostat in as well as apparently the absence of one can upset things. On the not...
  13. Thread: Ford 8100

    by essexpete
    Replies
    4
    Views
    477

    Re: Ford 8100

    1978 to 1981 according to the site above.
  14. Replies
    429
    Views
    292,814

    Re: Ford New Holland 8340 SLE help thread

    There is a floating plug adjacent to the fuse and relay box. I have not done it myself, but you need an on/off switch to access the codes. You do need to proceed with care armed with the codes. I...
  15. Replies
    83
    Views
    4,447

    Re: Gee you have won!

    So how far off are we from the end of Mrs May's premiership with all that has been going on. What about another general election?
  16. Thread: Ford 8100

    by essexpete
    Replies
    4
    Views
    477

    Re: Ford 8100

    http://www.tractordata.com/farm-tractors/008/9/8/8983-ford-8100.html

    No serial numbers.
  17. Replies
    10
    Views
    565

    Re: Case 4230 tractor

    Surely there must be a stamp elsewhere than just the cab.
  18. Replies
    10
    Views
    565

    Re: Case 4230 tractor

    Gapples might know, it was certainly on the RH side of the tombstone on earlier models.
  19. Replies
    83
    Views
    4,447

    Re: Gee you have won!

    Yes he should have resigned there and then at that meeting. BJ even ffukin worse the self serving b&st&rd.
  20. Replies
    11
    Views
    654

    Re: Massey 5465 getting hot

    Be careful removing the thermostat. On some engines it may allow coolant to bi-pass the rad.
  21. Replies
    10
    Views
    11,052

    Re: Fordson major chassis number????

    Quite right I wrote it the wrong way around.
  22. Replies
    10
    Views
    11,052

    Re: Fordson major chassis number????

    Use the link I have posted above.
    The casting codes that are usable are:
    F 19 X
    A 7 D

    Looks as though the number near the clutch is not complete.
    X is '55 and D is' 60.
    So far it looks...
  23. Replies
    11
    Views
    654

    Re: Massey 5465 getting hot

    It sounds like it might be linked to the transmission working harder.
  24. Replies
    2
    Views
    245

    Re: recommendations for a first Tractor

    Do you mean a side arm flail hedgetrimmer? What other duties? Have you steep slopes? There could be a massive difference in price, age, make and size within your budget. Do you need a loader?
  25. Re: MF124 square baler will not knot, splitting the twine. Any advice?

    I don't know anything about the MF124 but you could do with a bit more explanation for someone who might. Presumably you have a fault on one side only so have you done the obvious and compared. If...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4