Search:

Type: Posts; User: agrimax

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Re: Asking NH experts for NH TS115 rear axle advice

    It's the inner bearing that is a press fit. Proper way is to press the shaft out with a fabricated tool. On a 8340 axle,I recall setting something on the floor,solid and long enough to reach up the...
  2. Replies
    19
    Views
    689

    Re: MF 135 - Injection pump.

    Don't know if this illustration will be clear enough? Maybe ok if you zoom in.It's the same as the one in the Agco parts listings but they won't allow copying and pasting or even a screenshot and...
  3. Thread: Zetor 6718

    by agrimax
    Replies
    1
    Views
    103

    Re: Zetor 6718

    Apart from brakes,or lack of,they're not a bad old tool. The brakes are hyd operated,dry shoes and drums. The auto adjusters inside sieze up and the brakes just don't work,but simple enough to remove...
  4. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    Well done that man!!
  5. Replies
    19
    Views
    689

    Re: MF 135 - Injection pump.

    Here's an old thread zaza. Sounds simple enough.........Maybe save a couple of hundred!...
  6. Replies
    19
    Views
    689

    Re: MF 135 - Injection pump.

    Don't know what's involved in replacing the seal. Haven't been in that end of a DPA pump. Been under the lid and at the regulating valve etc but anything else and it's off to a specialist for me.
  7. Replies
    19
    Views
    689

    Re: MF 135 - Injection pump.

    No mention of torque settings for those bolts in either MF or Perkins manuals. Thinking they are 1/4'' unf (can't remember for sure) and likely around 10-15 ft/lbs. I just nip them up tight and hope...
  8. Replies
    19
    Views
    689

    Re: MF 135 - Injection pump.

    Might have mentioned it before,but stuff a piece of rag in between the gear and timing cover just in case a bolt drops out of the socket....
    Remove bolts and remove pump. The gear won't drop enough...
  9. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    I'll second that FF. ATF can work wonders.
  10. Replies
    7
    Views
    922

    Re: IH 2500 / 574 questions

    Hi Dandd and welcome to the forum.......
    Never heard of a 2500 but Google sorted that!Just an industrial 574 as you said.
    There are o rings at the bottom of the liners that become hard through...
  11. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    Think Murphy needs eradicated..! Flipping nuisance having to remove that bonnet and fuel tank again but....
    I'd say it would be worth having the injectors checked out properly but you could slacken...
  12. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    Probably this page you've seen John?
    http://www.agriline.co.za/technical/tappets_4cyl.html
    Yes,the rule of 9 is valid. Usually the clearances are set to 12 thou but I did see on a Perkins site to...
  13. Thread: Merry

    by agrimax
    Replies
    5
    Views
    636

    Re: Merry

    And to you.......
  14. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    Yes,it does sound like a poor repair from before. As long as every thing is well cleaned up......I sometimes use a belt sander and fine emery or a DA sander and go lightly.Leaves a good job.Probably...
  15. Replies
    31
    Views
    2,455

    Re: MF168 head gasket

    Hi John. You're right about the liners. They're just dry sleeves. I'd think it's just a head gasket is required. A little water has likely gotten into a cylinder making it hard to turn over.... It...
  16. Replies
    3
    Views
    1,152

    Re: New Holland 7840 SLE

    Do you mean the o rings in the top cover on the throttle shaft that goes through the lid? Have you got fuel coming through the bleed screw on the filter head when you push the primer? Can you hear...
  17. Replies
    1
    Views
    752

    Re: Case 4240 steering heavy.

    Filter and mesh bypass filter definately clean? Priority valve in the bottom front of the mcv polished up with fine emery and certain it's sliding free? Any easier to turn with the front jacked up?...
  18. Replies
    5
    Views
    1,516

    Re: Kohler vee-twin 20hp petrol.

    The fuel pump could have a perished diaphragm allowing fuel back down the vacuum tube and into the sump,or,and I think it will be more likely,either the float in the carb has stuck or the needle...
  19. Replies
    3
    Views
    928

    Re: Case jxu105 loss of drive and pto

    Maybe lift the floor out of the cab and check the wiring harness and if there are any multiplugs not making contact.
  20. Replies
    3
    Views
    928

    Re: Case jxu105 loss of drive and pto

    It does still sound like the seat switch or the wires to it are at fault,although it could be the damper plate on the flywheel has failed.Hydraulics would still be working as the pump is engine...
  21. Replies
    36
    Views
    6,793

    Re: A bit more help please ? MF 135

    I saved the paragraph and also copied and pasted it but either way it still wouldn't show when I put it in a post here. It was in the preview ok but not after sending the post.
    Maybe need to look at...
  22. Replies
    36
    Views
    6,793

    Re: A bit more help please ? MF 135

    Well Snipping tool is now on my taskbar! I'll try it in the future and then maybe have a look at Foxit too. Ta folks.
  23. Replies
    36
    Views
    6,793

    Re: A bit more help please ? MF 135

    Thanks zaza.I'm on Win 10 using Firefox. I'll have a play around later.
  24. Replies
    36
    Views
    6,793

    Re: A bit more help please ? MF 135

    John, assuming the light to be the same as in my 6270, turn it anti-clockwise to the fully off position and then with a bit of pressure turn it some more and the lens will come off.
  25. Replies
    36
    Views
    6,793

    Re: A bit more help please ? MF 135

    Sorry to jump in front of you again John................:)

    Thought I could have copied and pasted or took a screen shot of a paragraph in a PDF manual but it won't let me!
    Basically,oil that has...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4