Search:

Type: Posts; User: Footsfitter

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    8
    Views
    494

    Re: Modern technology!

    Two points John,

    Good to see you have finally set aside the tinnies and string :rolleyes:


    but there is a glaring hurdle you have forgotten to factor in- you would have to be selective on...
  2. Replies
    1
    Views
    548

    Does John Maddocks wear Blue pants?

    https://www.youtube.com/watch?v=XSZ9CtZ8oX4




    ;)
  3. Replies
    10
    Views
    1,191

    Re: JCB JZ140 360 track motor plugs problem

    Got a bit of round bar about the same OD as the plug- use it to welt it with a fair hammer and shock the plug and washer. A good 1/2" drive hex socket and knuckle bar may be required too
  4. Replies
    5
    Views
    1,073

    Re: Kohler vee-twin 20hp petrol.

    i think it'll be like Agrimax said.

    On Briggs & Stratton Pulsa-jet carbs they have a sheet diaphragm a spring pushes on and the crankcase pulsations makes the diaphragm pump fuel, close by using...
  5. Thread: Case CS78

    by Footsfitter
    Replies
    1
    Views
    561

    Re: Case CS78

    Had to google to see what CS78 is! Looks like what I'd call a stockmans tractor? Basic controls? has it got cable operated gear/range controls? See if it has and check that nothing on the outer...
  6. Replies
    1
    Views
    1,294

    Re: Replacement Hydraulic Rams

    Had short twin single acting rams for a dump trailer from Ramco- very good service.

    Had a hydraulic top link from Flowfit, very good all round except a bit longer delivery than was expected due...
  7. Replies
    5
    Views
    1,063

    Re: Starter motor

    http://www.aandrhandling.co.uk/
  8. Re: Original tiredimensions 1997 NH7840SLE?

    Being pally with the brilliant Michelin Rep we had, I'd give him the details of tyres and ratio off the plate and he would work it out as part of the estimate for new tyres unless we were 100% sure...
  9. Re: Original tiredimensions 1997 NH7840SLE?

    Look on the front axle for the makers plate which should have the gear ratio between the front and rear axles. With this info you can work out what tyre combinations will work ok. I expect there...
  10. Replies
    2
    Views
    598

    Re: New Holland to Manitou hitch

    Juggling around with Google and "LB110 Newholland digger to Manitou adaptor" came up with these two for you to try-
    ...
  11. Thread: foster d2p

    by Footsfitter
    Replies
    31
    Views
    10,154

    Re: foster d2p

    The little leyland my brother drove on the farm where I grew up. He thought something as simple as having the little lever on the quadrant to work the single spool valve as being really swish!! ...
  12. Replies
    30
    Views
    5,648

    Re: harvest in the 50's

    http://farmingforum.co.uk/forums/faq.php?faq=vb3_reading_posting#faq_vb3_attachments
  13. Replies
    10
    Views
    2,720

    Re: Mcconnel bale packer

    I think way back when i first started here there were still a couple of balls of poly string for the balepacker- it was much thicker, real HD stuff. IIRC the cine film shows Ted the balerman winding...
  14. Replies
    41
    Views
    14,993

    Re: Yellowhammers.

    Can't quite make out if any of them have a northern accent so maybe they are all southerners but for the last 10-14 days the buildings and roosts around the yards they swallows usually frequent are...
  15. Replies
    10
    Views
    2,720

    Re: Mcconnel bale packer

    Remember reading about them but before my time starting here although the farm were the proud owners of one and to tide you over here's a clip of it in action!

    ...
  16. Replies
    7
    Views
    1,219

    Re: Sandblastin diy

    +1!
  17. Replies
    5
    Views
    1,048

    Re: Matbro ts 290 hi-torque overheating

    Are the radiator and oil cooler cores clear? If the hoses are old and already folding a bit then its possible if one or more cores are restricting flow for the water pump to start cavitating where...
  18. Replies
    6
    Views
    2,675

    Re: Cooling system flushing

    Lads on a closed Technicians facebook page swear by dishwasher tablets. Reckon one of those is much better than anything else!
  19. Replies
    3
    Views
    1,231

    Re: Vintage tractor registration

    try the club/society for the make of tractor, they may have persons who have experience of doing it and also have guides/advice how to go about it. I'm recall it maybe one of the David Brown groups...
  20. Replies
    7
    Views
    1,252

    Re: MF 6465 Hard To Start

    I forgot to add a sort of simple summing up-

    option 1 -use an existing dirty engine and ad-blue+catalytic cleaners to the exhaust to clean it up post burn which will need a simpler/smaller...
  21. Replies
    7
    Views
    1,252

    Re: MF 6465 Hard To Start

    I think its a bit complicated like many regulations end up being?

    If this is any help, I think it all depends on basically how clean an engine is before they have to add extras to make lower...
  22. Replies
    7
    Views
    1,252

    Re: MF 6465 Hard To Start

    Sounds like you have an injector faulty which is temperature sensitive?

    Most common rail injectors are checked to see if they are loosing too much fuel through back leakage down the return line,...
  23. Replies
    36
    Views
    5,851

    Re: A bit more help please ? MF 135

    I've used Foxit reader for years, one quirk of it is you can double left click text in a PDF document and the arrow/hand pointer changes allowing the text to be highlighted and then selected/copied
    ...
  24. Replies
    36
    Views
    5,851

    Re: A bit more help please ? MF 135

    Just bin the lift pump. If you were to waste time and open up the diaphragm then at that age it will be well stretched instead of fairly flat, putting just a diaphragm in is a waste of money given...
  25. Thread: Boris

    by Footsfitter
    Replies
    139
    Views
    29,315

    Re: Boris

    A Labour club?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4