Search:

Type: Posts; User: agrimax

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: 1992 Ford 8340SLE error code 29 , I need help please

    It sounds like a problem I had years ago...was stumped for weeks as I had the clutch cable adjusted by the book after rebuilding the transmission.
    When depressing the clutch pedal,the cable pulls a...
  2. Replies
    13
    Views
    1,823

    Re: 1993 Ford 7740 sle issue(s)

    Thanks for letting us know. Useful to know for future reference.
  3. Re: Help with transmission noise International 354/444/434

    At a guess,I'd say the flywheel bolts are loose,or the toggle arms aren't running true and one may be touching the release bearing making it rattle. Pressing the clutch would tighten everthing up and...
  4. Replies
    2
    Views
    675

    Re: Back window on Case 895 xl

    Just the one on the RHS on the XL cab.
  5. Replies
    13
    Views
    1,823

    Re: 1993 Ford 7740 sle issue(s)

    At a guess, the ECU will have the capability to operate EDC even though you don't have it. I'd think the wiring harness will also be the same as EDC spec tractors but just a lot of the connectors and...
  6. Replies
    13
    Views
    1,823

    Re: 1993 Ford 7740 sle issue(s)

    Bit baffled by this one....Been looking at the manual and can only see those codes being related to what I said before.I assume you have mechanical top link sensing and the dash displays the...
  7. Replies
    13
    Views
    1,823

    Re: 1993 Ford 7740 sle issue(s)

    Yes,the codes are in the shop manual. Are you meaning your tractor doesn't have EDC? AFAIK,if it displays codes in the bottom right screen and normally shows the position of the arms as a number,then...
  8. Replies
    13
    Views
    1,823

    Re: 1993 Ford 7740 sle issue(s)

    Presumably you have an analogue rev counter but digital display to the rhs? SLE special perhaps?
    Code E16 is creeper solenoid open or short circuit or attempt made to engage creeper after prior...
  9. Thread: Jack caley

    by agrimax
    Replies
    34
    Views
    6,283

    Re: Jack caley

    Sorry to hear this Mark. Condolences to you and your family.
  10. Replies
    8
    Views
    1,438

    Re: Adverts appearing in posts

    Using Adblock Plus here (and Firefox) and no ads at all.
  11. Replies
    3
    Views
    1,069

    Re: Info on the zetor UR1 7 series

    Usually a good,reliable engine that starts in all weathers but you will need to use the excess fuel button on the inj pump.(Throttle full open and push the button in--it will come back out when...
  12. Re: Asking NH experts for NH TS115 rear axle advice

    It's the inner bearing that is a press fit. Proper way is to press the shaft out with a fabricated tool. On a 8340 axle,I recall setting something on the floor,solid and long enough to reach up the...
  13. Replies
    19
    Views
    2,524

    Re: MF 135 - Injection pump.

    Don't know if this illustration will be clear enough? Maybe ok if you zoom in.It's the same as the one in the Agco parts listings but they won't allow copying and pasting or even a screenshot and...
  14. Thread: Zetor 6718

    by agrimax
    Replies
    1
    Views
    888

    Re: Zetor 6718

    Apart from brakes,or lack of,they're not a bad old tool. The brakes are hyd operated,dry shoes and drums. The auto adjusters inside sieze up and the brakes just don't work,but simple enough to remove...
  15. Replies
    31
    Views
    5,320

    Re: MF168 head gasket

    Well done that man!!
  16. Replies
    19
    Views
    2,524

    Re: MF 135 - Injection pump.

    Here's an old thread zaza. Sounds simple enough.........Maybe save a couple of hundred!...
  17. Replies
    19
    Views
    2,524

    Re: MF 135 - Injection pump.

    Don't know what's involved in replacing the seal. Haven't been in that end of a DPA pump. Been under the lid and at the regulating valve etc but anything else and it's off to a specialist for me.
  18. Replies
    19
    Views
    2,524

    Re: MF 135 - Injection pump.

    No mention of torque settings for those bolts in either MF or Perkins manuals. Thinking they are 1/4'' unf (can't remember for sure) and likely around 10-15 ft/lbs. I just nip them up tight and hope...
  19. Replies
    19
    Views
    2,524

    Re: MF 135 - Injection pump.

    Might have mentioned it before,but stuff a piece of rag in between the gear and timing cover just in case a bolt drops out of the socket....
    Remove bolts and remove pump. The gear won't drop enough...
  20. Replies
    31
    Views
    5,320

    Re: MF168 head gasket

    I'll second that FF. ATF can work wonders.
  21. Replies
    7
    Views
    1,993

    Re: IH 2500 / 574 questions

    Hi Dandd and welcome to the forum.......
    Never heard of a 2500 but Google sorted that!Just an industrial 574 as you said.
    There are o rings at the bottom of the liners that become hard through...
  22. Replies
    31
    Views
    5,320

    Re: MF168 head gasket

    Think Murphy needs eradicated..! Flipping nuisance having to remove that bonnet and fuel tank again but....
    I'd say it would be worth having the injectors checked out properly but you could slacken...
  23. Replies
    31
    Views
    5,320

    Re: MF168 head gasket

    Probably this page you've seen John?
    http://www.agriline.co.za/technical/tappets_4cyl.html
    Yes,the rule of 9 is valid. Usually the clearances are set to 12 thou but I did see on a Perkins site to...
  24. Thread: Merry

    by agrimax
    Replies
    5
    Views
    1,175

    Re: Merry

    And to you.......
  25. Replies
    31
    Views
    5,320

    Re: MF168 head gasket

    Yes,it does sound like a poor repair from before. As long as every thing is well cleaned up......I sometimes use a belt sander and fine emery or a DA sander and go lightly.Leaves a good job.Probably...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4