Search:

Type: Posts; User: agrimax

Page 1 of 17 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    37

    Re: MF 5455 running on

    That'll be the latching valve in the pump at fault.Common issue with the Delphi pump.Don't know if the pump has to be removed or not for sure, to have it repaired but I've seen a new,modified...
  2. Replies
    417
    Views
    276,367

    Re: Ford New Holland 8340 SLE help thread

    Would your 7740 be one of the last I wonder? Never seen a three position switch in them but never used a very late model either to know.......
  3. Replies
    417
    Views
    276,367

    Re: Ford New Holland 8340 SLE help thread

    I would expect the ASC valve to still be there only you have to reach under the cab to move the knob. The quick lift switch shouldn't make the hitch disabled light come on. Should only come on if...
  4. Re: help needed to set the timing on a international 574 or might be a 674

    You might have no.1 piston on tdc but is it on the compression or exhaust stroke? You need the rocker cover off and when no. 1 piston is at the top,rockers 1 and 2 should be loose. If not, it's on...
  5. Replies
    417
    Views
    276,367

    Re: Ford New Holland 8340 SLE help thread

    Think as long as the rpms are at 1100 to start with,it'll be fine. The upper height cal seems ok.Try another calibration and after getting 99 for the upper limit, then go fully forward past the...
  6. Replies
    417
    Views
    276,367

    Re: Ford New Holland 8340 SLE help thread

    Yes. The lever needs to be past the detent for the external switches to work and should always be disabled in that bottom position. However,you should get 0 on the display before the lever is past...
  7. Replies
    417
    Views
    276,367

    Re: Ford New Holland 8340 SLE help thread

    67 doesn't exist.I think,although it says 67,it should read either 27 or 57. I think the first digit is being displayed wrongly. 27 is a fault with the left hand lift potentiometer and 57 is a fault...
  8. Replies
    15
    Views
    478

    Re: JCB 3CX - 1986 - Battery not chargung

    Do you have a battery light when you turn the key on?
  9. Replies
    1
    Views
    251

    Re: Bearings 20% discount until 31/05/2018

    I find them very good to deal with.And quick on delivery........
  10. Replies
    5
    Views
    397

    Re: Kubota ME8200 4WD

    http://www.kubota.cz/data/manualy/m-8200-n-wsm-en.pdf

    There is a wiring diagram near the end of the manual and unless I've read it wrong,I think there is a fuse linked to the 4wd system but the...
  11. Re: Massey Ferguson 35 Oil Pressure gauge Pipe

    Tidy looking Sam. Not convinced about the seat though...........:eek:
  12. Replies
    9
    Views
    767

    Re: international 584 losing oil

    If there is a noticable lip on the liners,then it would be worth replacing them and the pistons. If the tractor doesn't get much hard work and is ticking over a lot the bores will become glazed. A...
  13. Replies
    1
    Views
    224

    Re: Tyre size 7610 4wd

    16.9x38 or 16.9x34. The rolling radius is near enough the same for either to be used along with your front size.
  14. Re: Massey Ferguson 35 Oil Pressure gauge Pipe

    This is a Grey Fergie with the 20C engine but the pipe should be in the same place as yours....... Below right of the lift pump and behind the radius arm.I think....
    ...
  15. Replies
    20
    Views
    1,288

    Re: IH Hydro 84 Cylinder Head Gasket

    Assuming you're in the UK or ROI Dunny, 15w/40 would be the most suitable for your engine.
  16. Replies
    20
    Views
    1,288

    Re: IH Hydro 84 Cylinder Head Gasket

    True enough,there's 4 of them in below the cover.........Never even thought about the core plugs. Easy fix,hopefully.
  17. Replies
    20
    Views
    1,288

    Re: IH Hydro 84 Cylinder Head Gasket

    Even if you do find water passing the liner orings with a pressure test,don't just rush out and order new liners until you have the old ones out. At the age of the tractor,unless plenty of antifreeze...
  18. Replies
    20
    Views
    1,288

    Re: IH Hydro 84 Cylinder Head Gasket

    The engine is a D-246,the same as a 784 and the same head gasket set fits the majority,if not all the 74,84,85 and other 4 cylinder IH tractors.
    Make sure you refit the new gasket the right way...
  19. Replies
    4
    Views
    478

    Re: Massey 565 Diff Lock

    A few clevis's and pins underneath would need disconnected and freed up.
    https://screenshotscdn.firefoxusercontent.com/images/e1b4fe8a-6560-41ab-b539-b78601edcc6f.png
  20. Replies
    18
    Views
    1,314

    Re: New Holland 7840sle gearbox help please

    Brake pipes,handbrake cable,more wires and rear cab mounts diisconnected and the cab is ready to remove but it's more work and little benefit to take it off.Just as handy to tilt it back a bit. The...
  21. Replies
    18
    Views
    1,314

    Re: New Holland 7840sle gearbox help please

    It's a few years since I was in the 8240 I had.It was a prequad but wouldn't have been much different as far as gearbox removal is concerned. I think the first time I removed the gearbox,I split at...
  22. Replies
    18
    Views
    1,314

    Re: New Holland 7840sle gearbox help please

    Gearbox needs to come right out and a complete strip down to get the C3/C4 packs out. C1/C2 and F/R synchro pack needs to come out the front first and then carry on through to get 3/4 out the back....
  23. Re: ford / new holland rocker parts needed any ideas

    Doesn't make a lot of sense to me......As you say,the parts for the 8340 doesn't show the bit you're looking for but the 8360 list does show it but it comes as part of the rocker.Part numbers for all...
  24. Re: ford / new holland rocker parts needed any ideas

    Same rockers on the 60 series and the parts list shows the bits you need seperately there, but without part numbers meaning the whole rocker has to be bought! Typical. Looks like it's new rockers or...
  25. Replies
    2
    Views
    446

    Re: Matbro tr250 110 door handles

    Perhaps ACE will still have something about..........or if he doesn't see this,you'll get him here...www.aandrhandling.co.uk

    or if no luck,perhaps something here..........
Results 1 to 25 of 419
Page 1 of 17 1 2 3 4