Search:

Type: Posts; User: agrimax

Page 1 of 18 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    Any chance you are getting E32 code displayed on the dash? This is ''keep alive memory failure''. Sounds like it's not retaining the clutch calibration memory. There's supposedly a lithium type...
  2. Replies
    51
    Views
    10,841

    Re: mf3075 link arms bypass

    Hoff135 hasn't been on since Nov 2016........Maybe a poor chance he'll see your question......Jan 2013 since the last post on this thread.Maybe someone else will have what your after though.....
  3. Replies
    1
    Views
    227

    Re: 7840 sle ecu logic

    Can't help with the ecu and the fact that you said elsewhere you had it repaired/sorted would hopefully rule it out. Any chance of borrowing a known good one? Did you check out the fuseable links at...
  4. Replies
    3
    Views
    352

    Re: MF4225 gear stick linkage bushes

    Just had another look at the parts books and I see there is a second book for earlier tractors. I was looking at the later book. It shows a difference in the cabbed versions whereas the earlier ones...
  5. Replies
    3
    Views
    352

    Re: MF4225 gear stick linkage bushes

    Going by the parts book,there are only 2 bushes in total. Presumably(again going by the book) it's a cabless model John? Only the cabless have one bush in each end of the linkage. Cabbed models have...
  6. Replies
    2
    Views
    283

    Re: Serial number help

    That's not a serial number or casting number.The E1A parts simply denotes the model built between 1951 and 1964 and the rest of the number is a part number relating to the part it is cast into. You...
  7. Replies
    2
    Views
    171

    Re: V62 replacement rego

    Put in the chassis number.
  8. Replies
    8
    Views
    481

    Re: JCB 3CX 1986 Overheating

    Don't know how it's circulating properly without the thermostat,unless Jcb changed the system in later models.My 82 3CX will not circulate at all without the stat.
  9. Replies
    8
    Views
    481

    Re: JCB 3CX 1986 Overheating

    86=Perkins and it MUST have a themostat fitted.........
  10. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    I purposely didn't go there,when I had mine,for that reason Pete.Transmission problems cost me enough over 7 years without having to get a dealer involved!! Think it was the especially the H8 menu...
  11. Re: Can't remove Novacat 302 rear mower from tractor

    Are the arm stabilisers loose to start with? Have you tried taking up the weight of the mower on the arms before releasing the hook ends?
  12. Re: Massey Ferguson 5455 rear linkage problems

    By any chance have you unintentionally turned the depth wheel? Should be at 9 or 10 to give full drop.
  13. Replies
    10
    Views
    575

    Re: Case 4230 tractor

    Google suggests the number is only on a plate inside the cab, either above a door or the rear window on the 42 series........You would still think there would be a stamped number somewhere though. ...
  14. Replies
    10
    Views
    575

    Re: Case 4230 tractor

    Have a look on the rhs,above the axle,on the top flat of the bolster maybe beside the radiator. It may not apply to the 42 series but the 85 series had it there.May have continued with the 42.
  15. Re: any body know where to find engine number on bmc engine

    It should be stamped on a protruding flat on the block(where it meets the cyl head) just below number 4 injector.
  16. Replies
    1
    Views
    209

    Re: Mf 4370 link arms

    Presumably you have a thumbwheel for draft/depth control? Is it turned fully to the highest number? Turning it backwards ie decreasing the numbers,will reduce lowering.
    I think I've got it the right...
  17. Thread: Channy 64

    by agrimax
    Replies
    1
    Views
    201

    Re: Channy 64

    E54 is.... 5 volt reference failed,shorted to ground. Sorry, can't help more on what that means though. Must be a quad mod model with that code.Would guess there is a short somewhere about the...
  18. Replies
    7
    Views
    598

    Re: Marshall 702 questions

    Oil quantity for the transmission and back end(all one) from empty is around 55-60 litres. Either SUTO or UTTO and not straight hydraulic oil.2 speed pto was available on them but cant think where...
  19. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    Did you start it after filling with oil to refill the filters and then redip? Were the lift arms up or down when you drained it? Up and the internal lift cylinder and the assistor rams would still be...
  20. Re: one for the db members, why have a db 990 got an A after it?

    The ''A'' denotes livedrive-2 stage clutch. ''B'' designation denotes single clutch models.
  21. Replies
    1
    Views
    320

    Re: MF 5455 running on

    That'll be the latching valve in the pump at fault.Common issue with the Delphi pump.Don't know if the pump has to be removed or not for sure, to have it repaired but I've seen a new,modified...
  22. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    Would your 7740 be one of the last I wonder? Never seen a three position switch in them but never used a very late model either to know.......
  23. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    I would expect the ASC valve to still be there only you have to reach under the cab to move the knob. The quick lift switch shouldn't make the hitch disabled light come on. Should only come on if...
  24. Re: help needed to set the timing on a international 574 or might be a 674

    You might have no.1 piston on tdc but is it on the compression or exhaust stroke? You need the rocker cover off and when no. 1 piston is at the top,rockers 1 and 2 should be loose. If not, it's on...
  25. Replies
    429
    Views
    293,034

    Re: Ford New Holland 8340 SLE help thread

    Think as long as the rpms are at 1100 to start with,it'll be fine. The upper height cal seems ok.Try another calibration and after getting 99 for the upper limit, then go fully forward past the...
Results 1 to 25 of 439
Page 1 of 18 1 2 3 4