Search:

Type: Posts; User: Footsfitter

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 35 minute(s) ago.

  1. Replies
    2
    Views
    139

    Re: IH 674 problems

    I'm really shooting in the dark here, experience with these is nearly zero but a quick google for a hydraulic circuit brings up this site- ...
  2. Replies
    1
    Views
    172

    Re: 2014 case maxxum 120 multi controller

    Look for the wires into the compressor clutch (inside the pulley on the front) there could be one or two wires, a single should be just power and earth is through the compressor casing, two wires...
  3. Replies
    6
    Views
    1,493

    Re: on the land - Eastern Canada - update

    weather here has been proper upside down. Perhaps the walk in the park last summer is making this year seem worse?
  4. Replies
    9
    Views
    1,297

    Re: Claas Ares 656 problems

    Kings repair for dealers and manufacturers too. They have been fixing Ag electronics for years.
  5. Re: Tractor Pull - Richmond Corner, NB, Canada

    Back in 2012 when we went to the inaugural Austin F1 race we went south as well, one place we stayed at was San Antonio where they were holding an indoor pull!!


    ...
  6. Re: Mf 5455 rear linkage problem with mower conditioner

    That sounds very feasible. What about used parts from a breaker?
  7. Re: Mf 5455 rear linkage problem with mower conditioner

    I guessed the model but I expect they may be similar. Never had one of these Gima types off yet although given the rams are all external unlike the old ford/NH style with one in under the cover its...
  8. Re: Mf 5455 rear linkage problem with mower conditioner

    No5 is your cross or lift shaft with two arms, one either side although only one is shown below.



    https://i.postimg.cc/6qg9xHvL/snippings-005.png
  9. Re: Not agricultural but........................

    Often its just a case of alloy/steel corrosion and a methodical clean up of all contacting surfaces and points to ensure a good earth get things going. On Briggs & Strattons its the condensor and the...
  10. Re: Not agricultural but........................

    Take the fuel tank off, fill it with a couple a handfuls of small nuts, bit of diesel/parrafin and then swish about for a while to loosen up any crud/corrosion, empty out and flush clean. Sort out...
  11. Replies
    10
    Views
    1,477

    Re: Classic allsorts!

    I wondered if this lot they used would be a lax as that earlier sale a while back where you could still see the results.
  12. Replies
    10
    Views
    1,477

    Re: Classic allsorts!

    Hi Zaza, I'm hoping that it will be like the other system Thimbleby & Shoreland have used where if you use those original links above it they wil take you back to the lots after they are sold....
  13. Replies
    2
    Views
    625

    Re: Borg Warner T72/520-4 Loadall

    My guess would be old seals leaking in either the control valve or where the clutches mount onto the their shafts?

    The inching valve would only dump oil? Bet it'll be old hard seals.


    If...
  14. Replies
    3
    Views
    608

    Re: Matbro brake pedal leaking

    Always worth trying, nothing to loose neither
  15. Replies
    10
    Views
    1,477

    Re: Classic allsorts!

    Ha! good job it was only gloves! Should of checked what was on the clipboard- just pasted something from another board!!

    Put it right now, thanks for pointing it out.

    Good gloves though,...
  16. Replies
    3
    Views
    836

    Re: Cooling system flushing

    Yes, that would be a reverse flow. The difficulty is often that the flow of water at the rear of the water jacket around the rear cylinders is poor when flushing. When pulling wet liners out of the...
  17. Replies
    3
    Views
    608

    Re: Matbro brake pedal leaking

    I've heard this chap mentioned often-

    http://matbroman.co.uk/matbro-parts.html


    also theres these-

    https://tractec.grouphes.com/matbro-parts-spares
    ...
  18. Replies
    10
    Views
    1,477

    Classic allsorts!

    Heres a heads up for anyone who fancys an auction of someone's collection of nostalgia




    https://tsauction.co.uk/auction/vintage-auction-a-lifetimes-accumulation-of-artefacts/



    Run by...
  19. Replies
    62
    Views
    8,959

    Re: Euro elections

    I wondered that even though the Brexit candidate was a former Tory donor, perhaps Peterborough is a bit too "working class" to pouch a multi-millionare Tory Donor for an MP?
  20. Replies
    3
    Views
    836

    Re: Cooling system flushing

    Sometimes its worth trying to reverse flush an engine. If the rad is still out, remove the thermostat and connect up something with a decent flow to the bottom hose connection into the engine, a...
  21. Thread: JCB 536-60

    by Footsfitter
    Replies
    3
    Views
    856

    Re: JCB 536-60

    http://www.aandrhandling.co.uk/

    Could be useful ;)
  22. Replies
    62
    Views
    8,959

    Re: Euro elections

    I hope matey who's behind the summons is clean history wise.

    Read a little on the news app this morning and it looks like he's ineligible for "squeaky clean" already, by the time the media have...
  23. Replies
    62
    Views
    8,959

    Re: Euro elections

    And that simple fact will have skewed matters, but that won't worry the Lib-Dems, feeling born again their egos will be off the scale, will dear old Vince be able to cope with it all?
  24. Replies
    1
    Views
    441

    Re: MF 390 problem turning right.

    One or two rams? easier to track down if its one. I'd be looking at the seals/piston in the ram(s) sounds like oil is passing by a damaged seal or loose piston on its rod. The action of revving up...
  25. Replies
    2
    Views
    838

    Re: Citroen Godess Starter motor

    There's someone here about who's pretty good with copper extraction- 2 weeks ago this side of town had a few electrical issues at about 6am, a few off & on's an then it settled down except one part...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4