Search:

Type: Posts; User: essexpete

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    20
    Views
    4,155

    Re: Metal detecting- Yes or No?

    I let a guy who cold called do some detecting recently. I did sound him out first and he turned out to be a fund raiser for air Ambulance. Told him to call back in August post hay making. He did not...
  2. Replies
    38
    Views
    8,193

    Re: Yellowhammers.

    Swallow numbers low around our yard in Sth Essex.
  3. Replies
    14
    Views
    2,082

    Re: Massey Ferguson baler in haylage?

    Years ago I baled haylage with a MF 15 designed in the '60s. It was a short bale and dense. I only baled about 100 max at a time, slow but did not seem to cause a problem with steady care and sharp...
  4. Replies
    7
    Views
    1,000

    Re: IH Hydro 84 Rough Running

    Must be flat deck with tank under floor and they were fitted with electric pump. It would tick once the ignition switched on. Ours on the two we had failed but we found the main fuel pump would draw...
  5. Replies
    7
    Views
    1,000

    Re: IH Hydro 84 Rough Running

    Could do with Gapples or Richard W. If the power is lost at the top end, you don't have any undue/different noises and the fault is somewhat intermittent then it would still point to fuel to me. Have...
  6. Thread: Case 1455

    by essexpete
    Replies
    4
    Views
    962

    Re: Case 1455

    Sounds like you have found a gem then.
  7. Replies
    5
    Views
    818

    Re: New Holland air con

    If you are certain it is not climate control you could test to see if you have power to the thermostat switch and then try bridging out the switch.
  8. Replies
    4
    Views
    1,276

    Re: International 574

    Usual check for oil and coolant in the right places.
    Check to see if the handbrake works because it can be a PITA to sort. Drive through the high range gears up and down to check the syncros. You...
  9. Thread: Case 1455

    by essexpete
    Replies
    4
    Views
    962

    Re: Case 1455

    Most will tell you they are crap and best got shot of. I suppose I could take it off you if it is cheap.
    Joke apart I have never driven one but they always have a strong following and have been...
  10. Thread: JCB 536-60

    by essexpete
    Replies
    3
    Views
    1,007

    Re: JCB 536-60

    I have no idea specifically about the machine but have you checked:

    Run up to full working temperature to see that engine, transmission and hydraulics all work/perform as they should?

    Have you...
  11. Thread: Leyland 4/98

    by essexpete
    Replies
    18
    Views
    7,582

    Re: Leyland 4/98

    To the OP I would say does it start easily and does it burn any significant oil?
    If yes and no then why touch the engine? You could check to see that it running at the correct temperature when warm...
  12. Replies
    1
    Views
    988

    Re: Case Farmall 95a Linkage issues

    I think this is a Turkish built Case. I have no idea about your model but is it a mechanical or an electronic type lift?
  13. Re: Case MXM internal roof light for illuminating controls

    Is the MXM basically the same as a TM?
  14. Replies
    456
    Views
    339,914

    Re: Ford New Holland 8340 SLE help thread

    Have you got the transmission levers in the correct position for cal?
    Netherland site
    https://www.tractorfan.nl/topic/24059/
  15. Replies
    4
    Views
    1,579

    Re: Case maxxum 120 MC

    What are your hills like and what type of axles (number of studs) on the trailer?
  16. Replies
    1
    Views
    1,069

    Re: Hedge cutter cable controls

    If you can't trace through an agent or the original parts are ridiculously priced then do a Google search for bowden cable suppliers.
  17. Re: Ford 555C Electrical start problem - Help a Numpty please !!

    Surely shorting out the little spade terminal to the main input terminal on the solenoid would bypass any safety switches?
  18. Replies
    5
    Views
    1,323

    Re: ihc 574 gearbox/hydraulic problem

    Yes the Doncaster built tractors are all in one from the gearbox through to the rear including the oil immersed brakes. All the hydraulics share that oil as well. The dip stick will be on the left...
  19. Replies
    10
    Views
    3,828

    Re: Happy Christmas

    Yes a very Happy Christmas from Sarf Essix. As Joyce said here is to good health in 2019.
    Peter
  20. Replies
    6
    Views
    2,774

    Re: Fordson crawler puzzle?

    John if you google Fordson E27N County Crawler you will see a few.
  21. Replies
    7
    Views
    2,129

    Re: Sanderson teleporter 6-22 hydraulics

    Might have something in a manual. What is the problem?
  22. Thread: H Ferguson

    by essexpete
    Replies
    8
    Views
    3,728

    Re: H Ferguson

    There was a book about HF in my school library 45 years ago. Certainly one of my heroes then. Think I read it twice then a year on noticed when looking through the shelves that no one else had...
  23. Replies
    9
    Views
    5,017

    Re: Case 885xl too slow!

    If you are going to strip it down and you are subsequently going to use it sympathetically then why not rebuild in working order. I must admit that I have never rebuilt one as I was put off having...
  24. Replies
    3
    Views
    1,096

    Re: small/fine particles in the oil.

    A Case of driving on............ 🙂
  25. Replies
    2
    Views
    889

    Re: Tipping Trailer or Transport Box?

    Well it depends on what you most need for the main uses.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4