Search:

Type: Posts; User: essexpete

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: Boris

    by essexpete
    Replies
    79
    Views
    7,860

    Re: Boris

    Can't not agree with that.
  2. Thread: Boris

    by essexpete
    Replies
    79
    Views
    7,860

    Re: Boris

    I read in weekend paper that Cameron veiws Boris stance on Brexit as nothing more as a route to power. I have not an ounce of respect for Cameron but on this I think he right.
    If, and I hope it does...
  3. Thread: Boris

    by essexpete
    Replies
    79
    Views
    7,860

    Re: Boris

    Secret voting would also mean that an MP's constituents would be unable to check how their MP voted.
  4. Thread: Boris

    by essexpete
    Replies
    79
    Views
    7,860

    Re: Boris

    Was there not a compromise deal in place and the only one the EU would apparently agree to?
    The self serving Westminster twats from different political poles were never going to agree with one...
  5. Replies
    3
    Views
    410

    Re: Vintage tractor registration

    Sometimes it can be facilitated via a vintage club. If you have the original number plate and log book plus machine numbers you stand a good chance with DVLA.
  6. Replies
    459
    Views
    345,704

    Re: Ford New Holland 8340 SLE help thread

    Why are the spools in float position?
  7. Replies
    20
    Views
    5,483

    Re: Metal detecting- Yes or No?

    I let a guy who cold called do some detecting recently. I did sound him out first and he turned out to be a fund raiser for air Ambulance. Told him to call back in August post hay making. He did not...
  8. Replies
    41
    Views
    10,721

    Re: Yellowhammers.

    Swallow numbers low around our yard in Sth Essex.
  9. Replies
    14
    Views
    2,205

    Re: Massey Ferguson baler in haylage?

    Years ago I baled haylage with a MF 15 designed in the '60s. It was a short bale and dense. I only baled about 100 max at a time, slow but did not seem to cause a problem with steady care and sharp...
  10. Replies
    7
    Views
    1,113

    Re: IH Hydro 84 Rough Running

    Must be flat deck with tank under floor and they were fitted with electric pump. It would tick once the ignition switched on. Ours on the two we had failed but we found the main fuel pump would draw...
  11. Replies
    7
    Views
    1,113

    Re: IH Hydro 84 Rough Running

    Could do with Gapples or Richard W. If the power is lost at the top end, you don't have any undue/different noises and the fault is somewhat intermittent then it would still point to fuel to me. Have...
  12. Thread: Case 1455

    by essexpete
    Replies
    4
    Views
    1,065

    Re: Case 1455

    Sounds like you have found a gem then.
  13. Replies
    5
    Views
    898

    Re: New Holland air con

    If you are certain it is not climate control you could test to see if you have power to the thermostat switch and then try bridging out the switch.
  14. Replies
    4
    Views
    1,564

    Re: International 574

    Usual check for oil and coolant in the right places.
    Check to see if the handbrake works because it can be a PITA to sort. Drive through the high range gears up and down to check the syncros. You...
  15. Thread: Case 1455

    by essexpete
    Replies
    4
    Views
    1,065

    Re: Case 1455

    Most will tell you they are crap and best got shot of. I suppose I could take it off you if it is cheap.
    Joke apart I have never driven one but they always have a strong following and have been...
  16. Thread: JCB 536-60

    by essexpete
    Replies
    3
    Views
    1,111

    Re: JCB 536-60

    I have no idea specifically about the machine but have you checked:

    Run up to full working temperature to see that engine, transmission and hydraulics all work/perform as they should?

    Have you...
  17. Thread: Leyland 4/98

    by essexpete
    Replies
    18
    Views
    8,063

    Re: Leyland 4/98

    To the OP I would say does it start easily and does it burn any significant oil?
    If yes and no then why touch the engine? You could check to see that it running at the correct temperature when warm...
  18. Replies
    1
    Views
    1,009

    Re: Case Farmall 95a Linkage issues

    I think this is a Turkish built Case. I have no idea about your model but is it a mechanical or an electronic type lift?
  19. Re: Case MXM internal roof light for illuminating controls

    Is the MXM basically the same as a TM?
  20. Replies
    459
    Views
    345,704

    Re: Ford New Holland 8340 SLE help thread

    Have you got the transmission levers in the correct position for cal?
    Netherland site
    https://www.tractorfan.nl/topic/24059/
  21. Replies
    4
    Views
    1,842

    Re: Case maxxum 120 MC

    What are your hills like and what type of axles (number of studs) on the trailer?
  22. Replies
    1
    Views
    1,087

    Re: Hedge cutter cable controls

    If you can't trace through an agent or the original parts are ridiculously priced then do a Google search for bowden cable suppliers.
  23. Re: Ford 555C Electrical start problem - Help a Numpty please !!

    Surely shorting out the little spade terminal to the main input terminal on the solenoid would bypass any safety switches?
  24. Replies
    5
    Views
    1,360

    Re: ihc 574 gearbox/hydraulic problem

    Yes the Doncaster built tractors are all in one from the gearbox through to the rear including the oil immersed brakes. All the hydraulics share that oil as well. The dip stick will be on the left...
  25. Replies
    10
    Views
    3,945

    Re: Happy Christmas

    Yes a very Happy Christmas from Sarf Essix. As Joyce said here is to good health in 2019.
    Peter
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4