Search:

Type: Posts; User: powerfarmer

Search: Search took 0.02 seconds.

  1. Re: Contact for a company to recoat rubber roller

    Try Arolco
    http://www.arolcoirlltd.com
  2. Replies
    1
    Views
    680

    Re: Ireland - "the empire" strikes again

    That's very interesting, thanks for sharing.
  3. Re: Summers coming and so too is an early Aircon job

    Nice one
  4. Replies
    20
    Views
    5,214

    Re: Good to see us up and running again.

    Glad things are up and running again , Merry Christmas everyone
  5. Re: Wanting advice on Krone KR 125 and 130 balers

    Hi,
    6207-2RS bearings were fitted to the KR130 we used to run.
  6. Replies
    0
    Views
    743

    Mccormick CX clutch

    Hi All,
    I ve recently noticed a problem with our CX 100
    (Non xtra shift) .It has become difficult to change gear or direction when the tractor is running at more than tickover revs, it feels...
  7. Replies
    3
    Views
    1,530

    Re: Fuelling issue on Volvo l70c

    We ran Volvo trucks here years ago, they had aluminium dip tubes in the diesel tank running from near the bottom of the tank connecting to plastic fuel lines at the top. The aluminium tubes used to...
  8. Replies
    12
    Views
    6,016

    Re: Grass drying systems

    Hi Stephen,
    Something similar to this
    http://www.lasco.at/wp-content/gallery/blechkanaltrocknung/rundballentrocknung.jpg

    Except that the ducts were underneath and built into the sheds concrete...
  9. Replies
    12
    Views
    6,016

    Re: Grass drying systems

    Some very interesting replies, The video of the Claas Apollo is amazing. Its interesting how automated the system was and how developed it was by that stage.

    I have come across some archive...
  10. Replies
    12
    Views
    6,016

    Grass drying systems

    Hi all,
    I was recently re reading a book about the history of Claas. In it there is a chapter about the claas apollo a mobile green crop drying unit they built in the early 1970s. Oliver Walston...
  11. Replies
    17
    Views
    14,558

    Re: Are MF 500 Series Any Good?

    Have a read of the book "Inside Massey Ferguson a story of service" by David Walker, covers the introduction of the 500 series and lots more about MF from the 70s and 80s .

    Interesting...
  12. Replies
    5
    Views
    3,382

    Re: Mccormick CX lift error codes

    Thanks guys.I'll check it out.
  13. Replies
    5
    Views
    3,382

    Mccormick CX lift error codes

    Hi All,
    I ve got a query about our CX 100. It's currently showing an error code 5 on the display in the lift control panel (behind the seat under a little flap). The lift is working fine, but does...
  14. Replies
    17
    Views
    6,382

    Re: TANCO AUTOWRAP

    Is there a plate with the model no. on the lower part of the machine, near the drawbar?

    Manuals available here:...
  15. Replies
    15
    Views
    6,572

    Re: Can I put Hy-tran in a Massey?

    Hiya,
    I Just had a check in the McCormick operators manual it says hytran ultra. I dont know if the 590 has silicone rubber seals in its transmission/hydraulics . I just thought it would be...
  16. Replies
    15
    Views
    6,572

    Can I put Hy-tran in a Massey?

    Hi All,A query on oil.
    We have now two tractors an MF 590 and a recently acquired McCormick Cx100.The McCormick uses Hy tran in its trans and hydraulics, and will be sharing implements with the...
  17. Replies
    4
    Views
    1,299

    Case CX front axle oil leak

    Hi All,
    Our Case CX 100 has developed an oil leak in the front axle from where the drive shaft goes into the swivel hub.
    Is it much of a job to replace the seal?
  18. Thread: BFF WTF

    by powerfarmer
    Replies
    82
    Views
    33,317

    Re: BFF WTF

    Laughing like mad at that great description:)
Results 1 to 18 of 18