Search:

Type: Posts; User: ACE

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    1
    Views
    422

    Re: Matbro teleram not cutting silage

    Test the pressure, its probably the pump worn out. or maybe your quick release fittings are incompatible.

    An old Teleram probably doesn't operate at the high pressure a more modern matbro does and...
  2. Replies
    15
    Views
    9,663

    Re: Matbro TS 280 Transmission

    do a proper transmission overhaul, with a dyno test after to prove its right.

    Not uncommon to have to bore and sleeve the casings for the bearings when they are worn. also replace the transmission...
  3. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    1,091

    Re: Starter motor

    Hello

    New Genuine Iskra/Mahle starter 3.2kw 265 plus vat delivered to a UK address available from stock.
  4. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    1,091

    Re: Starter motor

    Thanks FF:)
  5. Replies
    5
    Views
    1,055

    Re: Matbro ts 290 hi-torque overheating

    It does not need a separate cooler, you have a fault on the machine. another cooler wont fix that. or you are simply using too high a gear for the task in hand.
  6. Replies
    5
    Views
    1,055

    Re: Matbro ts 290 hi-torque overheating

    Clean the radiator out and test the clutch pack pressures, if clutches are low and slipping that will overheat the oil although you should be getting poor drive IMO.
  7. Replies
    3
    Views
    1,116

    Re: Manitou 627 (2007) Brake issue

    Your problem is the brake piston seals in one or both axles. Very common there a newer style seal now much better.

    the axles have a vent but is a ball and spring type so not free venting and it...
  8. Replies
    3
    Views
    1,073

    Re: Jcb 530 crab steer problem

    no idea dont do much with JCB, i'm in to manitous and they have a far simipler steering system.
  9. Replies
    3
    Views
    1,073

    Re: Jcb 530 crab steer problem

    check the fuses again, all the lights will come on if the steering fuse blows.
  10. Replies
    15
    Views
    9,663

    Re: Matbro TS 280 Transmission

    boost diaghram on side of injector pump, rubber perished and you get no extra fuel when turbo on boost.
  11. Replies
    2
    Views
    1,249

    Re: Terex 250 Hydraulic Pump Failure

    chuck the pump away, fit a new one, clean the tank out, change the filters, replace the inlet section on the main valve block, reset all the pressures so the pump is working properly.

    Its almost...
  12. Replies
    2
    Views
    1,098

    Re: Borg Warner T72/520-4 Loadall

    Bevel Spring broken up jamming one clutch pack up. Was common back in the day.
  13. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Yeah sorry i have a habbit of doing that:D
  14. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Well IMO you could be opening a can of worms:( quite big ones :eek:

    I'm guessing here that its a 629 with side mounted engine and not a more recent rear engine 629 model?

    I say that because...
  15. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Transmission pressure switch is screwed in to forward clutch pack, its either a duff switch possibly leaking externally too, or your low on clutch pack pressure either from worn seals or worn pump or...
  16. Replies
    4
    Views
    1,462

    Re: Matbro 250 110 axles

    its permanent 4wd and limited slip diffs no manual diff lock. The OP's problem is wrong oil spec, I know this because I have a morris account and used xep90 a few times myself and had this problem,...
  17. Replies
    4
    Views
    1,462

    Re: Matbro 250 110 axles

    Hello

    Morris XEP90 oil is not the correct oil, you need Morris Terrain LS90. its a heavier duty commercial grade oil were as xep90 is more automotive grade LS90.

    Fuches Titan LS90 is also...
  18. Replies
    5
    Views
    1,268

    Re: Manitou MLT629 Road Gear Noise

    The 90 deg boxes can be a bugger to shim the mesh of the bevel gears correctly but your comment here on your opening post of this thread says to me bearings in main transmission or the diff pinion...
  19. Replies
    5
    Views
    1,268

    Re: Manitou MLT629 Road Gear Noise

    if its a newer MLT 629 with a rear mounted engine, then look at all the propshafts and the diff pinion bearings, possble can be transmission bearings but that gearbox is more reliable IMO, also look...
  20. Replies
    5
    Views
    1,268

    Re: Manitou MLT629 Road Gear Noise

    Hello

    Can you be more precise on the exact model spec? i will hazzard a guess its a MLT 629 120 LS powershift? if so it will be old between 1999 and 2002. the powershift gearbox on these were...
  21. Thread: Matbro teleram

    by ACE
    Replies
    5
    Views
    2,089

    Re: Matbro teleram

    Its a poor gearbox in them out of a Taxi, but yes they can still be overhauled, Wayne (matbro Man) knows them best.
  22. Replies
    9
    Views
    2,580

    Re: Brass filings in hydraulic oil in Terex 250

    Hello

    you need to lift the cab up one side normally the left hand side. get under there and have a look.

    might be the UJs on the propshaft or the damper coupling on the back of the engine, if...
  23. Re: Manitou MLT629T Recent Purchase and Have Some Questions

    increase that RPM to 900 it will run alot better.

    the way the valves on the ram work like that is normal, unscrew the adjuster to speed up the opening of the valve but with cold oil you will...
  24. Replies
    9
    Views
    2,580

    Re: Brass filings in hydraulic oil in Terex 250

    Inspection Hole in the tank is a bit small for a "Woofer" :D
  25. Replies
    9
    Views
    2,580

    Re: Brass filings in hydraulic oil in Terex 250

    Hello

    Trying to thing were them Brass bits may have come from! the only thing i can think of thats Brass in the hyd system on your machine is possibly the swash plate in side the hyd...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4