Search:

Type: Posts; User: JLRB90

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    8,582

    Re: New Valtra -T4 serie

    Does she come to demo it........:)
  2. Replies
    6
    Views
    5,153

    Re: trailer 12v electrics help

    As above. All vehicle lighting sockets now come fused. Best check that first
  3. Thread: Class or Case

    by JLRB90
    Replies
    17
    Views
    8,606

    Re: Class or Case

    Thats a major factor is the dealer backup and service. I hear Claas stand by their products very well too.

    Does the Case boost to that? Im not 100% on that one. Could be wrong thou.
  4. Replies
    10
    Views
    6,177

    Re: mccormick mtx120

    Thats the usual symtoms. It will more than likey always start fine. Up to temp, underload then you know its not right and like you say reeks like made. To me deffo pump timing gear has turned
  5. Replies
    10
    Views
    6,177

    Re: mccormick mtx120

    Done a good few like this now. Its a very common problem that the timing gear on the injector pumps turns slightly as the shaft is just tapered and not keyed/splined or similar. That to me definately...
  6. Thread: Class or Case

    by JLRB90
    Replies
    17
    Views
    8,606

    Re: Class or Case

    Id be thinking along the lines of the dealer knowledge and backup too. Does a puma 160 boost to 200???
  7. Replies
    21
    Views
    10,917

    Re: Case 956 bad starter

    Had the very same problem with my 956. New high crank/fast spin starter motor available from Startin tractors has solved the issue.
  8. Replies
    17
    Views
    7,635

    Re: Alternative to International 956xl.

    What this mans said!
  9. Replies
    8
    Views
    1,869

    Re: Renault spool block

    try this man.

    http://www.mcdonaghengineering.com/
  10. Replies
    16
    Views
    6,148

    Re: PTO DISCONECTING.

    Check the multi plug at the rear right of the cab for corrosion etc. These can give a multitude of problems.
  11. Replies
    16
    Views
    6,148

    Re: PTO DISCONECTING.

    whats the clutch problem?
  12. Thread: db 1190

    by JLRB90
    Replies
    7
    Views
    2,775

    Re: db 1190

    This is your man!

    http://www.mcdonaghengineering.com/
  13. Replies
    4
    Views
    1,658

    Re: MX170 damper plate question

    Is it a genuine case part or a repro? From MX110 to MX135'S the damper plates are no longer available and you have to fit the new improved versions but the flywheel needs a lot of specialist...
  14. Replies
    26
    Views
    12,546

    Re: Another tractor change thread...

    Lol. Claas have developed there own multilayer headgasket that they have been using for a while now. I believe Deere are now doing this too. So unfortunately no;)
  15. Replies
    13
    Views
    9,835

    Re: John Deere - Claas Engines

    Im afraid it IS mate....
  16. Replies
    11
    Views
    8,016

    Re: needles of a bearing in hyd oil

    Would be better to check out and sort it now at what could be a cheap and simple fix. However if you go by, "just keep running it" or "it'll get worse before it gets better" then bash on. You'll...
  17. Replies
    11
    Views
    8,016

    Re: needles of a bearing in hyd oil

    Obviously internal within the gearbox dude. Split job will be only way to reveal all
  18. Replies
    13
    Views
    9,835

    Re: John Deere - Claas Engines

    Tbh mate no........ block in Claas is stressed.
  19. Replies
    2
    Views
    781

    Re: international 856 gearbox parts???

    Yip, as above. Shit hot:)
  20. Replies
    8
    Views
    5,356

    Re: Case 5140 - brakes issue

    Pull the half shafts of dude. One of two things wrong. Either the piston seal is fcuked causing fluid to leak back into the backend or the brakes are just din. Either way its a half shafts off job...
  21. Replies
    15
    Views
    12,519

    Re: Case ih 5150 powershift issue

    Change the actual valve the solenoid operates not just the eletro-magnectic part.
  22. Replies
    4
    Views
    3,380

    Re: Claas mega 204 threshing

    Check your concave clearance is correct at the measuring points. If it is then close your concave up more and speed the drum up. This is more crop condition tbh
  23. Replies
    6
    Views
    3,903

    Re: Claas ares pto problem

    Check and clean the two large multiplugs at the rear of the cab as if the have the slightest of debris or corrosion they can cause a multitude of weird symtoms. This would be where id check next....
  24. Replies
    25
    Views
    9,822

    Re: Electronic enhancement differences?

    Because if updating or fault finding the values that will be displayed when it has been mapped will be extremly evident as most give you an expected figure to compare
  25. Replies
    22
    Views
    8,559

    Re: A question for expert mechanics!

    +1 for loctite 515. Drain the oil, remove the casing, clean the flanges with emery cloth and apply the stuff. Will seal anything.
Results 1 to 25 of 26
Page 1 of 2 1 2