Search:

Type: Posts; User: manx674

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    69

    international 674 brakes (again) lol

    hello, was trying to bleed brakes on my 674 today, one bled up fine the other not, i disconnected the pipe that comes from the master cyclinder just as it enters the rear end and started up the...
  2. Replies
    0
    Views
    496

    Forge - Services / Tractor parts direct

    Anybody know of or had experience of ordering from Forge - Services / Tractorpartsdirect lately? can't seem to get through to them and they owe me an order, website stays closed for maintenance.
  3. Replies
    3
    Views
    2,130

    cleaning out emulsafied oil from a 674

    The oil in the back end of my IH 674 has emulsified, what is peoples method for cleaning it all out?
  4. Replies
    0
    Views
    432

    Case 885 4wd, ZF axle wheel bearing

    hi, in need of some help, case 885xl, 4wd front hub bearings have failed and I'm trying to get the hub apart, I've got most of the outer disassembled but can't budge the gear wheel to get to the...
  5. Replies
    4
    Views
    2,534

    repairing hydraulic ram rod

    hi, got a double acting hydraulic ram rod that was left half exposed for some time and it has a pitted grove where the wiper was sat, I smoothed it out with fine wet and dry, that got the machine...
  6. Replies
    6
    Views
    1,729

    Re: International 674 brakes siezed

    with the tractor not running does the brake pedal press down any, steering wheel turn and if u put control lever down will the arms drop?
  7. Replies
    4
    Views
    1,782

    Re: finger bar converted to hydraulic drive

    the hydraulic flow rate in the tractor spec is 45l/min working pressure 175 kg/cm2 , it handles a bale wrapper with speed and ease no problem, just don't know what type/size of hydraulic motor to...
  8. Replies
    4
    Views
    1,782

    finger bar converted to hydraulic drive

    hi, I have an old but working Twose finger bar hedge cutter, it has a really long belt that drives the cutter bar, so when it gets worn and warm it has a habit of coming off or twisting over, was...
  9. Replies
    7
    Views
    3,863

    Re: Fuel Problems IH685

    I had similar problems on a 674, where the filters very bad? if so I would try an airline back down the fuel pipe to the tank, also drain tank and take out the taps and balance pipe check there...
  10. Replies
    2
    Views
    1,089

    International 674 / 574 radiator

    finding it difficult to source a new radiator for a international 674 and a 574, need whole radiators as cores aren't great and outside frame rotten beyond repair, only found one source so far, want...
  11. Thread: What is it?

    by manx674
    Replies
    25
    Views
    8,707

    Re: What is it?

    looks like it could be a the locking bar off a early yoke/crush head stock, twist on end just for looks, ring to lock it off, maybe :undecided:
  12. Replies
    5
    Views
    1,889

    MF 860 backhoe snapped shaft :(

    bit of a disaster day today, drive pinion/input shaft to rear axle snapped clean off at house after the UJ failed ( on the road :mad: ) anybody done one of these before?, best place for new parts?...
  13. Replies
    4
    Views
    1,943

    Re: Inta 674 high range lever

    All sorted now, took all the linkage off today, the high range pivot piece was stuck on the shaft, manage to leave it off the shaft but it left the bush behind it, rust had built up under bush making...
  14. Replies
    4
    Views
    1,943

    Re: Inta 674 high range lever

    it had been a bit stiff when first used, but I just put this down to it getting wet/ not using it in a while, it used to free up after a bit of use and be ok.
  15. Replies
    4
    Views
    1,943

    Inta 674 high range lever

    I was using my inta 674 today , everything was working as it should then just as I was finishing positioning a trailer I went to select high range and the lever went across the gate as normal but...
  16. Replies
    30
    Views
    13,422

    Re: Int 574 power steering issues

    if my memory is right :undecided:, one of the bungs has a valve/piston and spring under it and the other is the main relief valve for the hydraulics, this one has a fine gauze in the end ,held in by...
  17. Replies
    59
    Views
    21,249

    Re: Bale prick brute force & ignorance.

    take the tines off, place it face down( brackets up ) on a flat surface up against a solid wall/ uprightpost ect, place bottom of loadall carrage on bracket and jib out, or grip bracket in a 4 in 1...
  18. Replies
    4
    Views
    2,903

    Re: Teagle matchless mower

    heres some pics of what i've been offered, its on wheels at the moment, do u think skids would be better/work for the kinda work i want to use it for? does any of ur info say what size /length the...
  19. Replies
    4
    Views
    2,903

    Teagle matchless mower

    i've been offered a teagle matchless offset mower, anbody know anything about these?? can't seem to find much on web, was thinking of pos using it to cut some braken/rushes , it has what looks like a...
  20. Replies
    3
    Views
    1,710

    Re: vicon RC300 tedder manual

    when you change from transport to work position there is a choice of two holes, one puts it parallel to the back of the tractor, the other puts it on a slight angle, what difference does it make??,...
  21. Replies
    3
    Views
    1,710

    vicon RC300 tedder manual

    hi, has anybody got a manual for a vicon RC300 lying about that i could either buy off you or get a copy? or know where ther is one for sale??
    thanks
  22. Replies
    1
    Views
    1,385

    Vicon RC330 tedder, any good???

    i've been offered a vicon rc330 tedder, it also comes with one for spares, are they any good? what do i need to look out for??
    thanks
  23. Replies
    2
    Views
    1,079

    wrapping small squares with a round wrapper

    got a bit of baling todo, was going todo small square hay, but weathers not looking good, was thinking of haylage instead, i've got a small square baler , and an old Kvernaland 7525 wrapper (500...
  24. Replies
    12
    Views
    3,755

    Re: mf 265 3pt linkage controls

    yes it is hard to start, where is the heater plug switch? is it half way between ignition on and start?
  25. Replies
    12
    Views
    3,755

    Re: mf 265 3pt linkage controls

    thanks, thats great, had little play earlier and they work as u described, just another question , after start up should the red light wit the lightning strike on it go out or stay on? mine is...
Results 1 to 25 of 58
Page 1 of 3 1 2 3