If it's a genuine Marshall era block it's rare to need shims as they had the machining tolerances sorted by then .None of the Marshall's I ever did needed shims Of course unless you owned it from new...
Type: Posts; User: T P
If it's a genuine Marshall era block it's rare to need shims as they had the machining tolerances sorted by then .None of the Marshall's I ever did needed shims Of course unless you owned it from new...
Torque figures as below. Make sure you have fitted the correct liners as there are several variations and it won't last a month if you have the wrong one's in.
...
Regarding the lube engine oil is fine, I used to keep the injectors out of a rebuilt engine and crank the engine until I had oil pressure on a plug in gauge. Once oil pressure was established then...
There's a model of massey that has a single gear lever for the gears and ranges,some wee cheap pin or spring breaks in them I think for the range change if I remember correctly but it costs a lot of...
We have a 5460 with the rotary mechanical fuel pump,if yours is the same_. I would say to check two things, probably the first is to replace the electric lift pump/filter combo as there are rubbish...
We have a GD90 on a 1394 so it definitely fits. A QD90? should theoretically fit too and is a better loader primarily because the access is better for maintenance to the tractor due to the minimalist...
That sounds like "No2" .The pump is losing the prime while parked and having to bleed itself on starting. Try the grease trick around the seal to see if that helps. If it does you're looking at a new...
I once had a problem with frothy oil on a 40 series ford that turned out to be a defective filter vacuum switch. The switch that warns you when the pump is sucking hard on a blocked filter which then...
Do TS 115's normally have three friction discs and two static plates one side of the expander and just one friction disc the other? I only have a 40 series manual and it shows two friction discs and...
I'm currently helping a neighbour (mostly advisory) with what initially looked like a rear axle seal gone at the wheel of his TS115.He has the trumpet off and the bolt and planetary wheels off the...
If your machine uses the same bank slices (danfoss) as a small matbro there will always be power to the bank. There is a permanent 12v feed and a neutral . The direction or lack of movement is taken...
When a Chinese construction workers get electrocuted the foreman just gives the job to someone else. ;) You have to ask yourself at £40 what is the quality of the insulation on the wires etc and the...
Don't think I'd want to be up an Alumnium ladder leaned against an RSJ with a chinese inverter welder slung over my shoulder! Check out John Ward's youtube channel for chinese stuff.:D
If all else fails beat a section of old allen key in and carefully weld it to the plug then before it cools carefully loosen it with a bar and socket . When welding try not to undercut as it weakens...
Afraid not, this may or may not have the schematic you seek. If you send an ebay message the vendor will probably answer one way or the other as to whether the schematic is in it.
...
I'm thinking of buying two round bale stackers, one for me one for my neighbour. What are the owners opinions of the various makes. It'll probably end up a choice between nugent, fleming, mc hale...
What age of machine? Is it fitted with the old borg warner affair or the later ITL transmission,pictures would help. The ITL transmissions liked to rip the splines out of the torque converter...
My suspicion is that you have inadvertently introduced a little bit of debris into the load sensing lines somewhere and it is stopping a line check valve from seating. There is a check valve built...
https://stopthesethings.com/?s=total+flop
I bought some trailer jacks here and noticed these in passing:
http://www.autoandtrailer.com/muck-spreader-chains/
refreshing to to see a website with prices
Everything except the models indicated in that link used the holset brand turbo, ie the vast majority of all 4/98TT's ever built. The rare and not very good 904 had some tweaks for more power...
I am assuming that as the OP is fairly old it was overhauled by now and he's thinking of adding a turbo but information to go on what's actually taken place is scarce. Pics would help too.
From Memory I would tentatively recall that most of the tractors had a Holset brand one though I'll need to double check to be sure. One or applications used different brands of turbo. Contact...
My Father bought a new trailer with the Euro socket and adaptor several years ago, nothing but bother up until I cut it off and fitted an ordinary 7 pin plug to the trailer.
