Search:

Type: Posts; User: devonjohn

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    2,590

    Quicke loader subframe

    Wanted, Quicke DMX loader subframe to fit NH 8360
  2. Replies
    8
    Views
    4,734

    Re: Tm155 won't go into gear

    I have exactly the same problem with my 1998 8360 RC. What was the cure to this problem?
  3. Replies
    1
    Views
    1,043

    Quicke loader subframe

    Does anyone have any subframe brackets to fit a Quicke Q75 to an NH 8360
  4. Thread: Taarup 108

    by devonjohn
    Replies
    0
    Views
    625

    Taarup 108

    Does anyone have a 6 disc mower attachment for a Taarup 108 they could sell me?
  5. Replies
    12
    Views
    3,675

    Matbro 280 hub oil

    What oil should I be putting in my 1996 Matbro TS 280 hubs (Carraro axle)? Can I put 15-30 Suto in it, as that is what I put in the tractors with wet brakes. I do not want the brakes to chatter.
  6. Replies
    0
    Views
    1,077

    Wanted Loader for NH 8360

    I am looking for a loader to fit my NH 8360. Only need a basic loader and brackets, no valves needed. Need about 2.5 Ton lift. Loader off fire damaged tractor would be fine as long as loader is...
  7. Replies
    0
    Views
    708

    Loaders to fit NH 8360

    I have a NH 8360 4wd and want to put a loader on it about 2.5 ton lift capacity. Are the bracket fittings common with other tractors like the 8340, as the 8360 is rarely listed. If anyone knows of an...
  8. Replies
    1
    Views
    995

    Matbro TS280 hub

    I am looking for a complete left rear hub or hub parts for a 1996 TS280 Matbro with Carraro axle. As mine has broken up inside. Anyone know of any breakers who may have this?
  9. Replies
    5
    Views
    1,740

    Fiat 1000 starter

    Hello,
    Does anyone know what Iskra 4.2KW starter motor fits a 1974 Fiat 1000 tractor? It has engine number 8065-02. Any advice, I would be very grateful of.
  10. Replies
    4
    Views
    3,260

    Re: Matbro TS 280 hydraulic failure

    Has anyone got a schematic for the hydraulic circuit on this machine, I have one for a piston pump machine with load sensing etc. My machine is open centre, gear pump (timing gear driven) with...
  11. Replies
    4
    Views
    3,260

    Matbro TS 280 hydraulic failure

    This morning I started my machine and the steering was very stiff/solid, but the brakes and lift arm worked ok. About 3 minutes later everything stopped, the hydraulic arm would not move, and the...
  12. Replies
    6
    Views
    2,369

    Power assist clutch kit?

    Is there such a thing as an add-on kit to put on a tractor with a rod operated clutch pedal to make it power assisted. It can be hydraulicly operated from the tractor hydraulics, but I want it...
  13. Replies
    4
    Views
    1,882

    Re: Matbro TS280 noisy steering

    Thanks that would be great, I suppose the pressures are measured at the steering rams and if the pressures are out, the orbital unit would have to be removed and the valves adjusted?
  14. Replies
    4
    Views
    1,882

    Matbro TS280 noisy steering

    I have a 1996 TS 280 when I turn the steering wheel it makes a noise a bit like a trumpet. When the machine gets warm the noise gets louder. If I don't touch the wheel the noise stops. The steering...
  15. Replies
    2
    Views
    1,284

    NH 8360 Back end noisy

    I have a 1998 NH 8360 Range Command, its back end is a little noisy under power, any polite suggestions??
    Thanks
  16. Replies
    2
    Views
    1,074

    Taarup 108 Parts

    I am looking for a sprocket for a Taarup 108 standard, it is the one that drives the first bottom roller. Its part number is: 28.150.100. Please let me know if you know where I can find one. Thanks
  17. Replies
    4
    Views
    1,697

    Re: Taarup 106 knives

    Anyone had any luck finding any?
  18. Replies
    4
    Views
    1,697

    Taarup 106 knives

    Has anyone got in the corner of their workshop any new knives for a Taarup 106 they want to sell?
  19. Replies
    9
    Views
    6,735

    Matbro TS 280 Electrical Circuit Diagram

    I am trying to rationalise the electrics on my 1996 TS 280 but cannot find a circuit diagram for it. I am looking for a workshop manual for it. I have a manual that says TS270 TS280 workshop manual,...
  20. Replies
    11
    Views
    6,683

    Re: Matbro 1996 TS280

    How does the small hole in the priority valve dump enough pressure, i saw the hole and its tiny. Does it control the priority valve to dump the pressure rather than dump it directly? Would the engine...
  21. Replies
    7
    Views
    3,739

    NH 8340 vs 8360

    I am thinking of buying a late 1990s NH 8340 or 8360 any ideas or thoughts which one of these two would be best for general farm uses with occasional loader work.
  22. Replies
    11
    Views
    6,683

    Matbro 1996 TS280

    I have a Matbro 1996 TS 280. Once started it works well, however, it cranks over slowly when starting, not a problem in the summer but is difficult to start in winter. I have changed the battery and...
  23. Replies
    15
    Views
    9,976

    Matbro TS 280 Transmission

    I have a 1996 Matbro TS280, it does work well, only it is slow, it will climb the silage pit during buckraking, however it is slow, lots of revs are required to climb. Is there anything easy I can do...
  24. Replies
    36
    Views
    18,853

    Re: Matbro TS 280 Hydraulics

    Thanks, I will try the test, it does behave exactly as you describe with the oil getting hotter than it should, is the module repairable or will a new one need to be sought?
  25. Replies
    36
    Views
    18,853

    Re: Matbro TS 280 Hydraulics

    Ace, that sounds like the answer, what exactly does this module look like, is it bolted to the side of the valveblock? I will try the pressure shortly, I assume the answer is a new module?
    Cheers
Results 1 to 25 of 27
Page 1 of 2 1 2