Search:

Type: Posts; User: Etcetera

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    209

    Re: MF20 Baler, plunger pads

    [QUOTE=BonyTony;308675]Does anyone know what material the plunger wear pads on a MF20 baler are made from?

    i need a full set, 10 or a dozen pads but Iíll happily make my own!

    regards
    ...
  2. Re: List of Recoomended products for weed type?

    http://www.nufarm.com/UK/Commongrasslandweeds




    I had this bookmark saved - not sure if the products are still current, however main site is still working and has a fair bit of info. Years ago...
  3. Replies
    6
    Views
    928

    Re: Hedge Cutter Hydraulics

    Thanks. Was there once, I know my neighbour uses him for all his hose repairs so I'll be able to get his number.
    I usually go to Geofry in Kinallen for any hoses. I was delaying calling with him...
  4. Replies
    6
    Views
    928

    Re: Hedge Cutter Hydraulics

    Thanks, thats what I thought, just was a bit confused with the main ram having top and bottom pipes.
    I have a rear mounted shear grab which is plumbed in a similar way.. but the main ram on it only...
  5. Replies
    6
    Views
    928

    Hedge Cutter Hydraulics

    I need to replace the valve block on a Bomford 467 hedgecutter. Current pipe layout is as below.
    Return from main ram appears to be gravity & tee'd into return to tractor ( line 7).
    Could is be...
  6. Thread: shed paint

    by Etcetera
    Replies
    8
    Views
    1,876

    Re: shed paint

    If you mean red /blue / green oxide shed paint - Walkers Paints, Francis St Newtownards.

    ETC
  7. Replies
    2
    Views
    892

    Re: Fertiliser spreader convertion

    Some links to give you ideas:

    http://www.gleesonsteel.ie/Agricultural-Equipment/Bogies-for-Fertiliser-Spreaders


    http://www.sheamuscoonan.ie/fertilizer-bogie/


    ...
  8. Replies
    4
    Views
    1,206

    Re: intereferance in cb and radio

    Interference could be entering radio(s) from several sources - speaker cables, power cables, or antenna lead.

    A good earth from radio chassis to frame of tractor can help as will installing...
  9. Replies
    6
    Views
    1,826

    Re: Plastic electric fence posts

    There was an exhibitor ( from Cavan I think ) at the spring farm machinery show at the Maze, sorry I can't recall his name, he was displaying good lightweight angle galvanised posts.

    ETC
  10. Replies
    8
    Views
    1,522

    Re: Unfair postage charges NI

    Tell the retailer you are intend to inform the Consumer Council re discriminatory practice:

    http://www.consumercouncil.org.uk/filestore/documents/Statement_of_Principles_FINAL.png


    ETC
  11. Re: where is the best place to buy a phase converter single 240 to 3 phase 415 ,

    http://www.hucol.co.uk/static-converter-high-power-4-0kw

    Sorry last post was for lower power version, firm I worked in 30yrs ago used a a rotary Hucol ( if i recall right ), never gave any bother,...
  12. Re: where is the best place to buy a phase converter single 240 to 3 phase 415 ,

    http://www.hucol.co.uk/static-converter-1-1kw


    ETC
  13. Replies
    3
    Views
    1,804

    Re: Ford 550 backhoe help please

    Picture may help - rod FF is talking about #10
  14. Replies
    14
    Views
    9,669

    Re: 3.5 ton towing capacity van?

    http://www.parkers.co.uk/vans/news-and-advice/2016/march/best-vans-for-towing/


    ETC
  15. Replies
    20
    Views
    3,678

    Re: Dowdeswell or Kverneland Plough?

    KV ploughs more common in Ireland therefore there is better availablity of parts (genuine, generic and s/hand) on this side of the water, probabaly better resale value too.
  16. Replies
    0
    Views
    467

    Ford 655C buckets

    Can anyone provide me with the correct pin spacings for Ford 655c (extra dig)

    8" hitch width, 45mm pins, that much I know - the bucket thats on it has pins at 350mm, but neighbours Ford 555 is...
  17. Replies
    6
    Views
    3,082

    Re: Battery charger

    I would suspect the voltage regulator, if its for the scrapheap anyway I'd have a go a replacing it. Read the number on it and try CPC or RS for part. If youre like me and more used to 180amp welder...
  18. Thread: Bale stacking

    by Etcetera
    Replies
    18
    Views
    9,947

    Re: Bale stacking

    Yes you can fit a tipper to a front loader, I had this setup on a 2140 a few years ago, my neighbour still uses a similar setup with a Ford 7810. You have to be careful positioning them before you...
  19. Replies
    5
    Views
    2,697

    Re: Tablet software - dairy

    Just found this one tonight :

    http://openagtoolkit.com/apps/tillage/index.html

    it will also sync with https://trello.com/b/5m5yG3Cl/openatk-tillage

    may be useful where a farm has several...
  20. Replies
    6
    Views
    1,901

    Re: sourcing bulbs for knight sprayer box

    Try www.cpc.co.uk

    Good for most electronic components, and usually lightning fast delivery time any time I've used them.

    ETC
  21. Replies
    4
    Views
    3,489

    Re: Tablet mounts for a tractor

    I made one from a TV swivel wall mount ( retreived from a skip ) Deere 6400 has mounting points on front cab pillar. Laptop is a GOBOOK rugged PC & running Farmer GPS
  22. Replies
    52
    Views
    22,307

    Re: The Cost of Change

    As several posters have already pointed out and interesting and thought provoking post. Several years ago I had the good fortune to be taught by
    a business studies lecturer who had migrated from...
Results 1 to 22 of 23