Search:

Type: Posts; User: agrimax

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    155

    Re: IH 674 problems

    I'd suggest the priority valve in the mcv is stuck. If you look below the hyd filter but on the very bottom of the mcv block,there are 2 large plugs screwed up into the block. The one to the front...
  2. Replies
    1
    Views
    215

    Re: Oil change on JCB 260 skid steer

    http://jcbpro.ru/files/images/resized/products/3/2/32180-5b4b62dc32ea3.1100x800.jpgGoogle (and JCB parts) suggests this is the plug........
    Looks like a standard 6 sided allen key or hexagon bit in...
  3. Re: Stupid question but.............................

    I have a couple of Sealey ones as well. One switches on itself regularly but more so in low temperatures. The other decides itself whether it wants to be in metric or imperial but more often the...
  4. Re: 3 cylinder diesel ford engine in Sanderson Fork Lift

    Best take it off and get it serviced. Probably the metering valve is stuck although the regulating valve piston in the end you had off may be stuck as well. If you are confident enough,you could go...
  5. Replies
    4
    Views
    853

    Re: MF4225 hydraulics question

    Hi Christian,Can't seem to get that link to work either. That forum may be the same place as these links,I don't know....https://www.nuffieldtractor.com/index.php. Seems to go under this name...
  6. Replies
    4
    Views
    796

    Re: Air cooled engines

    Air cooled engines run hotter and however that affects things,creates problems in meeting emission targets.
  7. Replies
    7
    Views
    848

    Re: IH Hydro 84 Rough Running

    Just wondering,Did the Sekura cabbed hydros have an electric lift pump since the tank is lower down than those with the saddle tank behind the seat? Might be worth checking out......
  8. Replies
    7
    Views
    848

    Re: IH Hydro 84 Rough Running

    Or could be a blown head gasket..........
    Check the excess fuel/stop lever on the inj pump is travelling fully too.It's not stuck in the middle position by any chance? And check that the heater...
  9. Replies
    4
    Views
    957

    Re: International 574

    You say 574 in your first post and 475 in the second! If it's a 574,it should have a D239 engine.(D329 doesn't exist I think).
    If the engine hours are true,it hasn't done much in 30 years! Check the...
  10. Replies
    4
    Views
    853

    Re: MF4225 hydraulics question

    It'll be for float.It's the same on my MF 6270. Means you don't have to keep your hand on the lever when lowering a tipped trailer.
  11. Replies
    8
    Views
    1,494

    Re: Massey Ferguson 35 Fuel Injection Pump Issue

    But if it started and ran good on the borrowed pump it would still suggest that the new pump is the problem. It may be the correct fitting pump for a FE 35 but it mustn't be set up right internally....
  12. Replies
    11
    Views
    1,806

    Re: Oil seal on a teagle topper.

    Looks like it's time for a hydraulic puller or maybe the blue flame. On any toppers I've been at,that bit usually falls off the splines when the bottom nut is removed.
  13. Replies
    6
    Views
    935

    Re: MF 5455 gearbox splitter gear problem

    Sorry,still none the wiser after a good search.
  14. Replies
    6
    Views
    935

    Re: MF 5455 gearbox splitter gear problem

    Come to think of it(which I clearly didn't earlier):eek:,there would have to be a solenoid to make the change,wouldn't there! That switch above is likely just to change the H and L on the dash.Will...
  15. Replies
    6
    Views
    935

    Re: MF 5455 gearbox splitter gear problem

    Think it's a switch rather than a solenoid that you're looking for. Can't just find it on the Agco parts lists but found another diagram which shows a switch on the right hand side of the...
  16. Replies
    5
    Views
    1,030

    Re: Manitou MLT629 Road Gear Noise

    ACE is the man with the answers on anything Manitou. Maybe he'll look in soon.
  17. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    As always,FF,useful info.Thanks. Remember resealing a JCB 3C steering ram years ago and think it had the wire retainer but haven't dealt with that type since.
  18. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    Good you got it sorted.I was keen to know of the make up of these rams myself as I've seen questions asked about them before and no answers......
  19. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    Just had a look ''next door'' and the poster has got into his ram. So it is the type with the retaining ring accessed through the oil fitting.
  20. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    Right. Think I've got to the bottom of this...
    Copied and pasted from another forum. I'll not name it due to"historical conflicts" shall we say but you'll maybe know which one I mean!! Someone else...
  21. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    Unfortunately the diagram doesn't show enough in detail about the circlip. Presumably an internal clip going into a groove on the cylinder.Would have thought it should be visible on top of the gland...
  22. Replies
    12
    Views
    1,562

    Re: MF 80 loader main lift ram seals leaking

    The paper parts book from 1976 shows a retaining circlip where the rod enters the cylinder. Going by the book,the seals have different numbers for the short beam or long beam loaders.
    Short beam...
  23. Replies
    456
    Views
    336,125

    Re: Ford New Holland 8340 SLE help thread

    Had you the transmission oil well warmed up before calibrating? All wiring still intact near the battery? Big round multiplug above the batteries.....disconnect,spray with contact cleaner or such...
  24. Replies
    456
    Views
    336,125

    Re: Ford New Holland 8340 SLE help thread

    From the rear,look in on top of the lift cover, below the cab.
    The lift/lower valve block is just in front of the cross shaft. There's a solenoid on each end held on by 4 small internal socket head...
  25. Replies
    456
    Views
    336,125

    Re: Ford New Holland 8340 SLE help thread

    Is the top left knob on the EDC panel turned fully clockwise for fast drop?
    Are the pick up hitch rods sliding free?(if fitted)
    Or....lowering solenoid is faulty. You could swap it over with the...
Results 1 to 25 of 479
Page 1 of 20 1 2 3 4