Search:

Type: Posts; User: barth 140

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: jg plant

    by barth 140
    Replies
    1
    Views
    997

    jg plant

    anyone heard whats happened too jg plant ? in hereford
  2. Replies
    12
    Views
    2,974

    Re: ford 8340 injector pump timing

    is it a turbo 8340 if it is should leave 7840 standing ,needs more fuel not altering timing . Ive just changed a pump on a 7740 so pretty familiar with the set up
  3. Replies
    12
    Views
    2,974

    Re: ford 8340 injector pump timing

    the gear is keyed onto the pump shaft on a 40 series & you do rotate the pump body to alter pump timing if pump has been recond you shouldnt have too alter set it too 0
  4. Replies
    10
    Views
    5,739

    Re: Ford 5000 select-o-speed likely value??

    did you buy the selectospeed 5000 , id really like one used to know a farm near cirencester who had five of them they got on well with them
  5. Replies
    2
    Views
    2,345

    Re: ford 4000 hydraulic suction filter

    quite correct if you remove top cover & pump you can get filter right pain thats why they went too external filter on a 4600 ,you can attempt to clean it in situ if you remove cover & drain oil use...
  6. Replies
    18
    Views
    7,431

    Re: NH ts115 sle transmission light issue

    what age ts is yours ? does it have left hand shuttle by steering wheel
  7. Replies
    3
    Views
    1,198

    Re: NH T7.200 error code

    knew of similar problem cured with software update ,
  8. Replies
    3
    Views
    2,265

    c&o tractors - massey ferguson

    anyone know much about why c&o have taken on mf ,who sold massey in the area before ?
  9. Re: LUCAS/Delphi CAV DPA Injector Pump, low pressure output

    did you get it fixed ?
  10. Replies
    456
    Views
    335,486

    Re: Ford New Holland 8340 SLE help thread

    are you sure youve got the right calibration info for a quad mod 16/16 as its different to the earlier ones ,
  11. Replies
    5
    Views
    1,907

    Re: Ford 40 series fuel gauge

    fit a resistor equivalent to the sender on bottom tank being in full position on the wires too lower sender ,there must be another way though as some 40 series only had one tank i think (5640 ).
  12. Replies
    3
    Views
    1,198

    Re: NH T7.200 error code

    obviously a range command ,what year ?
  13. Replies
    7
    Views
    2,690

    Re: Help needed on tyre size (Ford 7840)

    the 4wd ratio is on the serial no plate under bonnet if i remember correctly ,
  14. Replies
    8
    Views
    3,362

    Re: Case equivalent to NH T6080 ?

    no 16/16 t 6080 range & pc only case equivalent is a 155
  15. Re: Which oil for backend of a Ford 6600 Year 1976

    pretty sure either is okay could also use a universal oil
  16. Replies
    5
    Views
    2,985

    Re: TM front suspension

    the control valve on a tm165 is completely different to a on the later tm such as a tm155 its much more complicated
  17. Replies
    5
    Views
    2,245

    Re: ford 5000 cracked pto

    pretty straightforward
  18. Replies
    5
    Views
    2,245

    Re: ford 5000 cracked pto

    if its an ordinary single speed pto which most 5000 s are you have too remove rh axle trumpet housing too get too the nut holding shaft in , 2 speed pto just remove circlip & pull out shaft
  19. Re: how to change a new holland 6010 from kmh to mph?

    does it have a keypad on top of dash ?
  20. Replies
    5
    Views
    2,245

    Re: ford 5000 cracked pto

    what exactly cracked the output shaft ?
  21. Replies
    1
    Views
    1,520

    terex t350 powershift

    we have a t 350 powershift which is very similar too a matbro ts 290 . it cant seem too make its mind up what gear its in & display shows e00 have been told its just a sensor any one know much...
  22. Replies
    9
    Views
    4,418

    Re: Ford/NH paint

    pretty sure that 40 series stayed with ford tractor blue changed too nh blue on tm & ts models
  23. Replies
    7
    Views
    4,402

    Re: Ts 115 no hydraulics when hot

    you say the spools stop working what about the 3pt linkage ? . a while since I had much to do with these but same as 40s sle ccls pump im thinking prob valve sticking in comp valve so pump stays on...
  24. Replies
    2
    Views
    1,021

    Re: NH 7740 Transmission Issue

    lubrication shuttle valve behind side plate has popped out did it happen suddenly ?
  25. Replies
    2
    Views
    1,639

    Re: county ploughman crawler

    cheers sawa yellow one for sale last year wish id bought it
Results 1 to 25 of 34
Page 1 of 2 1 2