Search:

Type: Posts; User: Gapples

Page 1 of 16 1 2 3 4

Search: Search took 0.31 seconds.

  1. Replies
    9
    Views
    2,826

    Re: Case 885xl too slow!

    If the plates are all missing it sounds as if someone has had it welded solid, this usually means they are in low TA.
    I believe there's now a kit available to lock them in high...
  2. Replies
    3
    Views
    777

    Re: small/fine particles in the oil.

    If it's like the dealer I worked at CNH have the ability to send off oil samples for analysis 👍
  3. Replies
    3
    Views
    894

    Re: Case 4230 Clutch finger settings

    Yes Pete, that's the screws I'm on about, I've seen them come out before. I can't for the like of me remember the number loctite we used, but if I was adjusting them I'd turn them in & out first...
  4. Replies
    3
    Views
    894

    Re: Case 4230 Clutch finger settings

    Done plenty clutches on these 42 series ... But as I worked at a CaseIH dealer we had the correct setting tool. If you have a new flywheel the chances are it will be ok. Certainly if the flywheel...
  5. Replies
    5
    Views
    1,376

    Re: Case IH 1056xl tractor

    I've sent you a few wiring diagrams to get you started, will sort out the rest for you tomorrow 👍:)
  6. Replies
    5
    Views
    1,376

    Re: Case IH 1056xl tractor

    Hi
    Give me your e mail address & I'll send you a few photos of the wiring diagram for the starting circuit.
  7. Replies
    5
    Views
    1,376

    Re: Case IH 1056xl tractor

    Hi
    I don't have my training manuals for the 56 series now, I sold them a couple of years ago.
    But I do still have sensodraulic manual & also wiring diagrams.
    What sort of help are you looking for ?
  8. Replies
    1
    Views
    1,426

    Re: international 674 brakes (again) lol

    Try bleeding the side that does bleed ok, tighten the bleed but & then try the other side by pumping the brake pedal, you could also try latching the pedals & pumping both pedals, the balance valve...
  9. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    This looks like the one you want

    https://m.ebay.co.uk/itm/INTERNATIONAL-TRACTOR-484-584-684-784-HYDRO-84-WORKSHOP-SERVICE-MANUAL-/290936960907
  10. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    Hi
    Yes the main hydraulic pump is behind that big block the hydraulic filter is bolted on to.
    You have to drain the oil & remove that block, it's called the MCV ( multi control valve )
    It's just a...
  11. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    Mmm not good, you have to ask where this award is coming from.
    Probably hand brake band & or PTO clutch material, but your right, the pump is probably on its way out & needs changed.
    Being a hydro...
  12. Replies
    10
    Views
    942

    Re: Case 4230 tractor

    No worries, pleased you found it 👍
  13. Replies
    10
    Views
    942

    Re: Case 4230 tractor

    Have to admit I would have thought rhs of front bolster as well, but if it's not on there well I don't know.
    If you take the panel off at the front rhs have look on top of the bolster, something...
  14. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    Hi
    Your welcome, I hope it's only that part at fault.
    Getting to it is not so easy, you have to take off the MCV, the big block the hydraulic filter bolts into.
    But when you drain the oil you can...
  15. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    PS
    Probably next test you want is with a flow meter if you have access to one.
    Plug into the auxiliary valve at the back & return oil into the filler bung.
    You should have approximately 8 gallons...
  16. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    It does sound like transfer pump issue then, the dipstick will read full, hydros hold quite a bit more oil than the standard tractor.
    The main hydraulic pump for arms & steering etc draws it oil...
  17. Replies
    13
    Views
    1,538

    Re: IH Hydro 84 - hydraulic pump??

    So in effect you have no hydraulics at all ? Does the hydrostatic drive still work ok ?
    Do any hydraulics work again if the tractor has been left a while ?
    Or if you put an extra couple of gallons...
  18. Re: 1990 fella drum mower- how do i remove skid pans???

    No worries Hugh
    As long as you've found how to do the job 👍
  19. Re: 1990 fella drum mower- how do i remove skid pans???

    Never done a Fella but I remember an old niemeyer, not sure of spelling, had a large Allen screw holding the bottom disc on.
    You needed a special long tool, supplied with these mowers that fitted...
  20. Re: help needed to set the timing on a international 574 or might be a 674

    Drop the push rods in & watch them as you turn the engine
  21. Re: help needed to set the timing on a international 574 or might be a 674

    There should be a pointer on the front of the engine pointing at the crank pulley.
    Get a bit of Emery tape & clean up the pulley, there are timing marks on it.
    Find the marks with 10 & 20 on them,...
  22. Replies
    3
    Views
    787

    Re: CASE 4230 Hydraulics

    All you need to take off initially is the seat etc to get that plate off & see inside the hydraulic top cover.
    Try to see if anything is broken, if it is then yes, you'll have to take the cab off,...
  23. Replies
    3
    Views
    787

    Re: CASE 4230 Hydraulics

    I've seen a few bits inside those hydraulic top covers break.
    The part that is splined onto the cross shaft occasionally splits along a spline right through the retaining allen screw.
    Also seen the...
  24. Replies
    10
    Views
    1,206

    Re: Hydro 84 - Power Steering

    Hi
    The MCV ( multi control valve ) Is on the transmission on the left hand side.
    Get down under the cab steps ( LHS ) look up in behind the LHS back wheel, you should see a large rectangular block...
  25. Replies
    2
    Views
    1,489

    Re: Inter national 784 series?

    ???
    Work out the series ?
Results 1 to 25 of 376
Page 1 of 16 1 2 3 4