Search:

Type: Posts; User: ACE

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Manitou MLA 628

    by ACE
    Replies
    6
    Views
    3,088

    Re: Manitou MLA 628

    Afraid that is the price its actually 1735.11 retail so your already getting a good discount off it. I though i might have had a better price for you but i cant so i'm OUT.

    Dont waste your time...
  2. Thread: Sanderson 726

    by ACE
    Replies
    2
    Views
    938

    Re: Sanderson 726

    or just order a vapormatic VPK5574 which is a fleetguard exactly the same as original.
  3. Thread: Sanderson 726

    by ACE
    Replies
    2
    Views
    938

    Re: Sanderson 726

    If its not a speedshift or powershift model a manitou transmission filter will fit and work fine;) 561749. BUT only if its the manual gearstick.
  4. Replies
    1
    Views
    512

    Re: Manitou 523T Series 1

    The brake fluid pot is in the cab under the dash, use LHM mineral fluid only. That nipple is just a bleed nipple for brakes, unless the brakes need attention just leave them alone, they are a pain in...
  5. Replies
    5
    Views
    1,070

    Re: Manitou 527 engine oil light

    yes they do and many years ago i fitted a brand new Lucas bulb and the bulb had been made wrong! filaments were the wrong way round.
  6. Thread: Jcb is

    by ACE
    Replies
    2
    Views
    2,187

    Re: Jcb is

    :D Blinking JCB's:rolleyes:

    To be honest not seen one of them in ages, will be the old type similar frame to a old 525-68 etc just bigger?

    Wouldn't have thought it would have many cut outs on...
  7. Thread: Blue Antifreeze

    by ACE
    Replies
    3
    Views
    1,021

    Re: Blue Antifreeze

    Blue is just universal antifreeze as far as i know. Normal stuff not red long life etc or an organic type.
  8. Replies
    3
    Views
    868

    Re: Terex 250 Wiring Problem

    Thats not quite right Trevor!

    The lift and tilt do have a 12 volt feed BUT it isn't supposed to be permanent, there is a micro switch in the centre of the sticks, so when you move the stick off...
  9. Replies
    3
    Views
    1,469

    Re: Matbro teleram not cutting silage

    Test the pressure, its probably the pump worn out. or maybe your quick release fittings are incompatible.

    An old Teleram probably doesn't operate at the high pressure a more modern matbro does and...
  10. Replies
    15
    Views
    11,812

    Re: Matbro TS 280 Transmission

    do a proper transmission overhaul, with a dyno test after to prove its right.

    Not uncommon to have to bore and sleeve the casings for the bearings when they are worn. also replace the transmission...
  11. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    1,795

    Re: Starter motor

    Hello

    New Genuine Iskra/Mahle starter 3.2kw 265 plus vat delivered to a UK address available from stock.
  12. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    1,795

    Re: Starter motor

    Thanks FF:)
  13. Replies
    6
    Views
    2,184

    Re: Matbro ts 290 hi-torque overheating

    It does not need a separate cooler, you have a fault on the machine. another cooler wont fix that. or you are simply using too high a gear for the task in hand.
  14. Replies
    6
    Views
    2,184

    Re: Matbro ts 290 hi-torque overheating

    Clean the radiator out and test the clutch pack pressures, if clutches are low and slipping that will overheat the oil although you should be getting poor drive IMO.
  15. Replies
    3
    Views
    1,482

    Re: Manitou 627 (2007) Brake issue

    Your problem is the brake piston seals in one or both axles. Very common there a newer style seal now much better.

    the axles have a vent but is a ball and spring type so not free venting and it...
  16. Replies
    3
    Views
    1,631

    Re: Jcb 530 crab steer problem

    no idea dont do much with JCB, i'm in to manitous and they have a far simipler steering system.
  17. Replies
    3
    Views
    1,631

    Re: Jcb 530 crab steer problem

    check the fuses again, all the lights will come on if the steering fuse blows.
  18. Replies
    15
    Views
    11,812

    Re: Matbro TS 280 Transmission

    boost diaghram on side of injector pump, rubber perished and you get no extra fuel when turbo on boost.
  19. Replies
    2
    Views
    1,576

    Re: Terex 250 Hydraulic Pump Failure

    chuck the pump away, fit a new one, clean the tank out, change the filters, replace the inlet section on the main valve block, reset all the pressures so the pump is working properly.

    Its almost...
  20. Replies
    2
    Views
    1,418

    Re: Borg Warner T72/520-4 Loadall

    Bevel Spring broken up jamming one clutch pack up. Was common back in the day.
  21. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Yeah sorry i have a habbit of doing that:D
  22. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Well IMO you could be opening a can of worms:( quite big ones :eek:

    I'm guessing here that its a 629 with side mounted engine and not a more recent rear engine 629 model?

    I say that because...
  23. Re: Manitou MLT629 Hydraulic alarm only in forward gear!

    Transmission pressure switch is screwed in to forward clutch pack, its either a duff switch possibly leaking externally too, or your low on clutch pack pressure either from worn seals or worn pump or...
  24. Replies
    4
    Views
    2,104

    Re: Matbro 250 110 axles

    its permanent 4wd and limited slip diffs no manual diff lock. The OP's problem is wrong oil spec, I know this because I have a morris account and used xep90 a few times myself and had this problem,...
  25. Replies
    4
    Views
    2,104

    Re: Matbro 250 110 axles

    Hello

    Morris XEP90 oil is not the correct oil, you need Morris Terrain LS90. its a heavier duty commercial grade oil were as xep90 is more automotive grade LS90.

    Fuches Titan LS90 is also...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4