Search:

Type: Posts; User: ACE

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Manitou

    by ACE
    Replies
    4
    Views
    551

    Re: Manitou

    You could also have a fuelling issue, injectors and the injector pump, make sure the automatic timing is working, sensor in the head next to the dash temp sender works a solenoid on the bottom of the...
  2. Thread: Manitou

    by ACE
    Replies
    4
    Views
    551

    Re: Manitou

    take the rad out and clean it properly in side and out, back flush it and replace the water hoses which often perish internally, change the thermostat (dont run without one will make it worse)
    ...
  3. Re: Manitou 627 mlt 2007 bypass all safety protocols?

    Sounds like it might be yes, think the last one i bought was around 40??? but you might want the pins and plug for it too if thats iffy, manitou do sell that but its on a special PDF file that...
  4. Re: Manitou 627 mlt 2007 bypass all safety protocols?

    bypass the seat switch fine, the pads are crap and they set fire sometimes anyway!

    transmission fuse is F8 i think but you pull that out it wont go any where.

    its possibly the hand brake...
  5. Re: Terex T200/T25 or Matbro TR200/250 Transmission oil leak

    Top yoke is the same as the bottom ones, you will have to tip the cab over a bit one way or the other to get in there, take exhaust off or you will knacker it, watch out for the handbrake cable and...
  6. Re: Terex T200/T25 or Matbro TR200/250 Transmission oil leak

    Look closer there is a big circlip behind the yokes, but i did get it wrong slightly its actually an internal circlip not a external one.
  7. Replies
    4
    Views
    2,083

    Re: Marshall 802 engine rebuild

    Make sure to check the liner standing height and shim as required or you will be blowing head gasket and doing it all again
  8. Re: Terex T200/T25 or Matbro TR200/250 Transmission oil leak

    You seem a bit confused about what model you have!

    T200 has a stake nut in the centre. There is a torque setting for this nut, BUT i think/sure it has a collapsible spacer in the gearbox to set...
  9. Thread: Manitou MLA 628

    by ACE
    Replies
    6
    Views
    4,900

    Re: Manitou MLA 628

    Afraid that is the price its actually 1735.11 retail so your already getting a good discount off it. I though i might have had a better price for you but i cant so i'm OUT.

    Dont waste your time...
  10. Thread: Sanderson 726

    by ACE
    Replies
    2
    Views
    1,509

    Re: Sanderson 726

    or just order a vapormatic VPK5574 which is a fleetguard exactly the same as original.
  11. Thread: Sanderson 726

    by ACE
    Replies
    2
    Views
    1,509

    Re: Sanderson 726

    If its not a speedshift or powershift model a manitou transmission filter will fit and work fine;) 561749. BUT only if its the manual gearstick.
  12. Replies
    1
    Views
    855

    Re: Manitou 523T Series 1

    The brake fluid pot is in the cab under the dash, use LHM mineral fluid only. That nipple is just a bleed nipple for brakes, unless the brakes need attention just leave them alone, they are a pain in...
  13. Replies
    5
    Views
    1,770

    Re: Manitou 527 engine oil light

    yes they do and many years ago i fitted a brand new Lucas bulb and the bulb had been made wrong! filaments were the wrong way round.
  14. Thread: Jcb is

    by ACE
    Replies
    2
    Views
    5,285

    Re: Jcb is

    :D Blinking JCB's:rolleyes:

    To be honest not seen one of them in ages, will be the old type similar frame to a old 525-68 etc just bigger?

    Wouldn't have thought it would have many cut outs on...
  15. Thread: Blue Antifreeze

    by ACE
    Replies
    3
    Views
    2,455

    Re: Blue Antifreeze

    Blue is just universal antifreeze as far as i know. Normal stuff not red long life etc or an organic type.
  16. Replies
    3
    Views
    1,878

    Re: Terex 250 Wiring Problem

    Thats not quite right Trevor!

    The lift and tilt do have a 12 volt feed BUT it isn't supposed to be permanent, there is a micro switch in the centre of the sticks, so when you move the stick off...
  17. Replies
    3
    Views
    3,167

    Re: Matbro teleram not cutting silage

    Test the pressure, its probably the pump worn out. or maybe your quick release fittings are incompatible.

    An old Teleram probably doesn't operate at the high pressure a more modern matbro does and...
  18. Replies
    15
    Views
    14,610

    Re: Matbro TS 280 Transmission

    do a proper transmission overhaul, with a dyno test after to prove its right.

    Not uncommon to have to bore and sleeve the casings for the bearings when they are worn. also replace the transmission...
  19. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    3,655

    Re: Starter motor

    Hello

    New Genuine Iskra/Mahle starter 3.2kw 265 plus vat delivered to a UK address available from stock.
  20. Thread: Starter motor

    by ACE
    Replies
    5
    Views
    3,655

    Re: Starter motor

    Thanks FF:)
  21. Replies
    6
    Views
    4,123

    Re: Matbro ts 290 hi-torque overheating

    It does not need a separate cooler, you have a fault on the machine. another cooler wont fix that. or you are simply using too high a gear for the task in hand.
  22. Replies
    6
    Views
    4,123

    Re: Matbro ts 290 hi-torque overheating

    Clean the radiator out and test the clutch pack pressures, if clutches are low and slipping that will overheat the oil although you should be getting poor drive IMO.
  23. Replies
    3
    Views
    1,809

    Re: Manitou 627 (2007) Brake issue

    Your problem is the brake piston seals in one or both axles. Very common there a newer style seal now much better.

    the axles have a vent but is a ball and spring type so not free venting and it...
  24. Replies
    3
    Views
    3,568

    Re: Jcb 530 crab steer problem

    no idea dont do much with JCB, i'm in to manitous and they have a far simipler steering system.
  25. Replies
    3
    Views
    3,568

    Re: Jcb 530 crab steer problem

    check the fuses again, all the lights will come on if the steering fuse blows.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4